Low beams will not come on

Bright lights wont shut off ? Assume you mean high beams ? Reading how they work might thing high beam relay has stuck contacts inside .

Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Your best bet , take your vehicle to a qualified repair shop . Before you want to replace the BCM . . Professional tech would check for DTC'S - diagnostic trouble code's in the BCM before replacing part's that are not needed .

No signal at signal wire on relay ???? Which circuit wire mite that be ? Hooking up a factory or professional scan tool to view input data from the switch would also be a good step .

Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Headlamps Inoperative - Low Beams
Step
Action
Yes
No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference: Master Electrical Component List
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle
2
Place the headlamp switch in the HEADLAMP position.
Place the headlamp dimmer switch in the LOW position.
Do the low beam headlamps illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections
NO - Go to Step 3
3
Disconnect the turn/headlamp switch connector C2.
Connect a 15-amp fused jumper between the headlamp low beam signal circuit and a good ground.
Do the low beam headlamps illuminate?
YES - Go to Step 4
NO - Go to Step 5
4
Inspect for poor connections at the harness connector of the turn/headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 7
NO - Go to Step 6
5
Repair an open or high resistance in the headlamp low beam signal circuit. Refer to Circuit Testing and Wiring Repairs .
YES - Did you complete the repair?
NO - Go to Step 7
--
6
Replace the turn/headlamp switch. Refer to Turn Signal Multifunction Switch Replacement .
YES - Did you complete the replacement?
NO - Go to Step 7
--
7
Operate the system in order to verify the repair.
Did you correct the condition?
YES - System OK
No - Go to Step 2

It's more then likely the dimmer switch .

DTC B2575
Circuit Description
The body control module (BCM) turns on the LOW BEAM relay when the ambient light sensor senses a dark condition or the low beam headlamps are requested ON. Battery positive voltage is supplied to the LOW BEAM relay at all times. The BCM grounds the LOW BEAM relay control circuit in order to activate the relay.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2575 Headlamp Control Circuit

B2575.01
Will set if there is a short to voltage in the low beam relay control circuit.
B2575.06
Will set if there is an open or short to ground in the low beam relay control circuit.

Did you check low beam fuses for voltage, with headlamps on lo beam? Use a testlite to check for voltage. In the diagram you see the lo/hid relay, correct? I'm not saying the relay is faulty, you need to check voltage and ground. The bcm and dimmer switch are involved, I don't know if check for headlamp/lighting trouble codes will help? Don't replace anything unless your testing points in the direction.

First check light relay fuse, if ok check battery voltage at low beam light terminal, if ok replace low beam bulb, if no voltage check switch side of relay, if voltage replace relay, if no voltage check headlight low beam switch.

There is no low beam relay.

Both your low beam and your high beam is protected by the same fuse, so it makes sense that the fuse is OK if the high beam is working on the passenger side. There are 3 fuses for the headlamps. Fuse #13 in the Battery Junction Box (20 Amp). If this fuse is blown, the headlamp relay will not have any power and neither high nor low beam on either side will work (you will have no headlamps at all) Then there is Fuses #2 and #3 (15 Amp) in the Battery Junction Box. #2 goes to the left low and high beam and #3 goes to the right low and high beam.
The headlamp switch uses a SINGLE CIRCUIT to control BOTH sides at the same time, so if one side works, the switch cannot be the problem. The headlamp relay provides power for fuses #2 and #3 and we already ascertained that these fuses must have power since we have working lights on both sides, so the relay cannot be the problem. A replacement bulb has already been tried, so that pretty much leaves us with a bad lamp socket. (Most likely cause) or a bad connection at splice #S122, which is located in the main wiring harness near the breakout for the left headlamp. (RED/BLACK wire)

you don`t say if you have checked the fuses for the headlights.if the fuses are okay and you know that the low beam filaments are working.you may have to feed power and ground directly to the proper headlight prongs from the battery to make sure the bulbs are good.then it could be a relay for the low beams or a switch for the headlights.you don`t say if you have daytime running lights on this car as there is a module for this system that may be the problem for the now low beams.

The headlight relay has probably failed. This relay is in the underhood fuse box. There are typically two of the same relays in there, so you can swap the low-beam relay for the high-beam relay to verify the problem before you shell out $30 for new relay.

did you check for a relay in your fuse panel? there should be a relay that controls your low beams and one for your high beams. check for that and then if high beams are working swap it with low beam relay. if your problem switches to low beams working and high beams not working replace the bad relay.

do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal

1. CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
   Remove the lower driver's side footwell trim.

1. Detach the lamp switch bezel.
   • Remove two screws.

1. Remove the light switch.
   • Remove three screws.
• Disconnect the electrical connector