2007 Cadillac CTS-V Sedan Logo

Related Topics:

A
Anonymous Posted on Nov 22, 2013

How to unclog windshield washer tube + cadillac cts 2007

Windshield washer wont work and the reservoir seems to be full.

4 Related Answers

Lorenzo Lamanna

  • 113 Answers
  • Posted on Aug 18, 2009

SOURCE: I need a picture of the windshield drain on a 2001

You need to clean out the cabin filter drain tube. The cabin filter housing allows the air to enter the cabin through the HVAC system. When water gets in here, the drain tube allows it to escape. If the drain tube is plugged with leaves and dirt, the housing fills up and it overflows into passenger floor area.
Remove the filter, clean the drain tube (prepare to get your feet wet) and put in a new filter.
The filter is below the pass side WS wiper under the plastic cover.

Ad

Anonymous

  • 389 Answers
  • Posted on Apr 19, 2010

SOURCE: windshield washer stays on too long

Do you have one of those washers that wants to wsh the whole car for yu when you only need the window done? I am thinking it is in the switch that you push or turn to make it squirt. I will venture a squirt of WD 40 in the switch will solve this problem? Just something you can try, Please give me a good thunbs up for the guess if you please. I need the good marks, Let me know if it worked, Raz

Anonymous

  • 571 Answers
  • Posted on Jun 08, 2010

SOURCE: My windshield washer does not spray on my Cadillac

1. No liquid
2. burned fuse
3. Pump dead
4. Something clogged in the system (tubes, nozzles etc).
5. Leaking/disconnected tubes

Anonymous

  • 10319 Answers
  • Posted on Nov 25, 2010

SOURCE: 1999 Cadillac DeVille, no power to windshield

the pump is located in the reservoir and is probably shorted out. You are lucky it lasted this long. You need to get a replacement at any GM dealer

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

When I turn the switch to my 2006 Cadillac DeVille CTS windshield wiper it does nothing no sound no movement what is wrong

Hard to say what's wrong without testing thing's . Is there B+ voltage to the wiper switch ? B + voltage to the wiper motor ? Do you know how to use a voltmeter ? How to test electrical circuits ?
Here is a factory service manual list of componets involved .
Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Do you know how the wipers work ?
Windshield Wiper Motor Wiring Tutorial
Wipers Inoperative - All Modes ?????
Wiper Motor Switch Troubleshooting

1helpful
1answer

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out

The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.
  1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
    Remove the bolt and the windshield washer reservoir filler neck.
  1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
  1. Remove the foam filler and remove the retainer.
  1. Remove the 2 screws and the accessory drive splash shield.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the nut, 2 bolts and position the A/C accumulator aside.
    • To install, tighten to 9 Nm (80 lb-in).
  1. Unclip the A/C lines from the inner fender well.
  1. Drill out the rivet and remove the bracket.
  1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
    • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
  1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
  1. Disconnect the electrical connector from the windshield washer pump.
  1. Release the wiring harness from the reservoir, and remove the washer reservoir.
  1. To install, reverse the removal procedure.
0helpful
1answer

My windshield washer reservoir won't hold washer fluid.

The seam on the windshield fluid container is broken and leaking like crazy.
0helpful
1answer

06 cts when you turn wipers on windshield washer pump runs continually if you turn the wipers off the water shuts off. I have replaced the (D01 D6377D -) Windshield Wiper & Windshield Washer...

-I believe the switch is bad. The line to the pump might stuck at the wipe position. So every time it on. It turn both
devices on.
Check it out.

Good luck


Mai
3helpful
1answer

My windshield washer does not spray on my Cadillac CTS. What is the problem?

1. No liquid
2. burned fuse
3. Pump dead
4. Something clogged in the system (tubes, nozzles etc).
5. Leaking/disconnected tubes
0helpful
1answer

Windshield washer stays on too long in my cts 2007

Do you have one of those washers that wants to wsh the whole car for yu when you only need the window done? I am thinking it is in the switch that you push or turn to make it squirt. I will venture a squirt of WD 40 in the switch will solve this problem? Just something you can try, Please give me a good thunbs up for the guess if you please. I need the good marks, Let me know if it worked, Raz
5helpful
1answer

Windshield washer fluid reservoir - MB ML 350

right where the lines connect to reservoir, has little black seals that leak. I recommend removing reservoir, empty it out, then use RTV silicone and place it between seals and reservoir. Let it dry for FULL day. than reinstall.
0helpful
2answers

Wiper fluid level sensor replacement

Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Not finding what you are looking for?

77 views

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...