Engine light on how to reset

the engine light notifies of a problem
not being able to reset the light indicates that there is a problem
take it to an accredited specialist service center to have it properly diagnosed and reset

About 10,800 results (0.85 seconds) Search Results

DIY: Reset Check Engine Light without OBDII reader ...

? 3:31
https://www.youtube.com/watch?v=TvBcdjLkBhU
Jul 1, 2014 - Uploaded by Christian Macias
Learn how to reset your Check Engine Light (CEL) withoutusing an OBD II 2 scanner / reader tool. Will work on just about... Also referred to as Service Engine Soon, and Malfunction Indicator Light (MIL). This is very general ...Missing: l200

Service Wrench Light - YouTube

? 1:34
https://www.youtube.com/watch?v=S8pvlJNUkW8
Feb 17, 2009 - Uploaded by richpin06a
... reset sequence; this was the reason for the two indicator lights..... My 2002 Saturn LW300 V6 has this light come on after driving 40 KM (25 ... My service engine soon light is on, on my saturns series (2001) how would i check mine?.. i dont have the scan tool, but i did hear of using a paper clip before.

How to Reset the service engine light on a Saturn S-Series ...

vehicle-maintenance.wonderhowto.com/.../reset-service-engine-light-satu...
Apr 30, 2010 - It is never a good sign when the 'check engine' light comes up on your

2010 KW T800 How to reset engine check light ' TruckersReport.com ...

www.thetruckersreport.com > ... > Kenworth Forum

Nov 8, 2011 - Is there a way to reset Engine Check Light without going to dealer? ... Inmy case it was 3725. If I run with ... 2013 Kenworth Dash panel removal.Missing: 1997 ‎t600

DIY: Reset Check Engine Light without OBDII reader ...

? 3:31
https://www.youtube.com/watch?v=TvBcdjLkBhU
Jul 1, 2014 - Uploaded by Christian Macias
Learn how to reset your Check Engine Light (CEL) without using an OBD II 2 scanner / reader tool. ... Year ...

The Check Engine light must be reset using an OBD-II code reader. Dealers have them as do repair shops. Places like AutoZone will read the codes for you, but normally will not reset the Check Engine light due to possible liability issues. You can purchase a code reader at these places to do this yourself. Make sure you get one that can read and reset the engine light. The very cheap ones cannot reset the Check Engine light.

Reset oil service light Honda Pilot. From years: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012.
How do you reset oil service light Honda Pilot. From years: 2003, 2004, 2005.

1. Turn off the engine. Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
2. Hold the button for at least 10 seconds, until the indicator resets.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

How to reset oil service light Honda Pilot. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.
Resetting the Engine Oil Life Display if maintenance service is done by someone other than your dealer, reset the maintenance minder as
follows:

1. Turn the ignition switch to the ON (II) position.
2. Press the select/reset knob repeatedly until the engine oil life is displayed.
3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.
4. Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.

All information is taken from the Honda Pilot owners manual.

most engine lights are reset using a code reader so find a shop with a code reader and see if the light will reset

There are three ways to reset a check engine light.

1. Disconnect the battery, wait approximately 30 minutes, reconnect the battery. This resets the cars computer which also reset the check engine light. On newer OBD (on-board diagnostic) compliant vehicles this usually does not work. See step 2.

2. Reset using an OBD II reader. When you hook an OBD II code reader up to your vehicle, you can reset the computer using the code reader.

3. Fixing the problem. Generally the check engine light comes on for a reason. Usually it is emission related (sensors, gas cap) or electrical (faulty wiring). In this case the way to reset the check engine light is to fix the problem

Go to your local O'Rielly's or Autozone. They will tell you the code and reset it for free. Otherwise take the negative battery cable loose for about 10 min. This will clear the ECM, but you won't know what tripped the light! Best Wishes, TJ

there is no light for emissions testing on this vehicle. there is a ses light that can come on, indicationg a problem with the engine or transmission electronic system. this will require a scan tool to pull trouble codes. there is another light called oil life monitoring that needs to be reset after oil changes, which I suspect is what you are seeing. here is a picture of the light and the instructions for resetting.,

The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL SOON message being turned on, reset the system.
After changing the engine oil, the system must be reset as follows:

1. Turn the ignition to RUN, with the engine OFF.
2. Press the information and reset buttons on the Driver Information Center (DIC) at the same time to enter the personalization menu.
3. Press the information button to scroll through the available personalization menu modes until the DIC display shows OIL LIFE RESET.
4. Press and hold the reset button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
5. Turn the key to LOCK.

If the CHANGE ENGINE OIL message comes back on when you start the vehicle, the Engine Oil Life System has not reset. Repeat the reset procedure.

If you bring it back to the mechanic who last serviced it he will gladly reset it free of charge.