Mustang rear seat removal?

Mike Raatz

• 435 Answers
• Posted on Jun 08, 2010

SOURCE: how do i remove the back seat to my 2000 ford

On the seat bottom left and right of center there's a release clip. (see photo) Carefully push the release with a flat screw driver and pull up doing one side at a time.
Once the seat bottom is removed there's 2 bolts holding the seat back in place, remove the bolts and lift the seat back straiting up.

Marvin

• 85242 Answers
• Posted on Nov 13, 2008

SOURCE: how do I set the clock on my 2003 Ford Mustang 2 door coupe

Here is a link to your owners manual at Fords web site, download it and look on page 22 for the procedure to set the clock.

http://www.motorcraftservice.com/pubs/content/~WO3MUS/~MUS~LEN/42/03musog5e.pdf

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .

1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .

1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.

1. Remove the differential pinion shaft (4211).
   1. Remove the differential pinion shaft lock bolt (4241).
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Remove the U-washer (4N237).
   1. Push the axle shafts (4234) inboard.
   1. Remove the U-washer.

1. CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
   Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. CAUTION: Do not damage the wheel bearing oil seal.
   Remove the axle shaft.

1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.

1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
   Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.

1. Lubricate the new rear wheel bearing with the specified lubricant.

1. Using the special tools, install the new rear wheel bearing.

1. Lubricate the lip of the new wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Using the special tools, install the new wheel bearing oil seal.

1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

1. Lubricate the lip of the wheel bearing oil seal
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Do not damage the wheel bearing oil seal.
   Install the two axle shafts.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Install the U-washer.
   1. Position the two U-washers on the button end of the axle shaft.
   1. Pull the axle shaft outward.

1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
   Install the differential pinion shaft.
   1. Align the hole in the differential pinion shaft with the case lock bolt hole.
   1. Install a new differential pinion shaft lock bolt.

1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.

1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. Install the rear brakes. For additional information, refer to Section 206-04 .

1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .

1. Lower the vehicle.

SOURCE: how to remove rear seat back 1987 mustang

Tools Required:

• 3/8 inch Drive Ratchet
• 3/8 inch Drive 3” Extension
• 3/8 inch Drive 10mm Socket
• 3/8 inch Drive 13mm Socket
• T-50 Torx Bit
• 1/4 inch Allen Wrench
• 3/16 inch Allen Wrench
• 1/2 inch Wrench
• Drill Motor
• 1/8 inch Drill Bit
• 5/16 inch Drill Bit
• 2 inch Hole Saw
• Trim Tool (Fork Tool)
• Electrical Tape
• Center Punch
• Hammer

1. Locate the retainers securing the seat bottom into the vehicle, approximately 10 inches from the end of the cushion, either side. Use your thumb to push in retainer release tab. Lift the seat up to remove.
2. Remove the two 13mm screws securing the seat back, located on each lower corner. Lift seat upward to release seat back from brackets at the top. You can carefully prop the seat back under the retracted top , use caution if choosing this method not to damage or scratch the vinyl of the seat. You can remove the seat from the vehicle completely by disengaging the flanges securing the top of the rear seat to the fabric of the convertible top well .
3. Remove Quarter Trim Panels:
   
   1. Grip the Quarter Trim Panel Cap at the shoulder strap opening and lift up to dislodge the retaining clips.
   2. The inside Quarter Trim Panels are two-piece panels. Remove the upper portion of the Quarter Trim Panel from the vehicle; it is not necessary to remove the lower portion. Pull the forward edge of the trim Panel over the pinch weld in the doorjamb.
   3. Use a Door Trim Tool (Fork Tool) to dislodge the pushpin retainer at the rear edge of the Trim Panel approximately 4” down from the top, pry Trim Panel toward the outside of car to release retainer.
   for more help click this link directly
   
http://www.americanmuscle.com/05-07-lightbar-install.html ---------

Tom Shanks

• 141 Answers
• Posted on Mar 10, 2010

SOURCE: Headliner install in 66 mustang coupe

Remove windshield and rear window to do it properly. Headliner is actually crimped in between window gaskets and roof edge. Not a job for the faint at heart. If you don't know the string trick to get your gaskets in place you'll be working on it this time next year. Look on CJ Pony parts web site. They used to have a good tech article on headliner replacement. Hope this helps...