Remove front bumper - 1995 Nissan Maxima

Question edited for clarity.
Question moved to model category.

Assistance installing a retainer for bumper filler

Tacoma World https://www.tacomaworld.com > threads > assistance-i...

Dec 30, 2020 - A couple of weeks ago, I removed most of the front end to do three things. Repaint the lower valance (faded) :thumbsup: tackle some rust ...

Front Bumper Filler Install Problems - Tacoma World
Nov 22, 2011
Headlight Filler/Bumper Filler Clips? Are these it?
Dec 7, 2017
2012 TACOMA FRONT END CONVERSION RG11 ' Page 10
Sep 1, 2013
Another bumper filler question ' Tacoma World
Dec 15, 2015
More results from www.tacomaworld.com

How do I install the retainer for a front bumper filler on a

Fixya https://www.fixya.com > ... > Cars & Trucks > Toyota
5 hours ago - Remove the front bumper cover. Remove the tool box and the luggage compartment trim (carpet). Remove the 2 bolts and the nut. ... To install:.

Toyota Tacoma Retainer, front bumper filler, no.3

Toyota Parts Direct https://www.toyotapartsdirect.ca > Toyota__Tacoma
RETAINER, FRONT BUMPER FILLER, No.3. This Fits Your Toyota Tacoma. Part Number: 5252335020. Supersession(s): 52523-35020. RETAINER. Fits Tacoma (1995 - 2001)
Rating: 4.6 · ‎1,922 reviews · ‎$3.58

..

Remove the 2 6 mm bolts that attach the bumper to the front corner of the fender. Remove the 2 6 mm nuts that attach the bumper to the frame in the front of the car. Remove the 4 6mm bolts securing the grill. Gently remove the bumper from the front of the car.You could take your car to a mechanic or to the dealership to take off the bumpers on your car and to repair the bumpers.

There are some steps that help you to easily remove Front Bumper :
1. Open the hood of your car.
2 . Look under the edge of the front of the car at the end of the bumper.
Pull the plastic shield down out of the way if it doesn't come off completely. Reach behind the bumper at each corner and you should find a bolt holding the corner of the bumper to the car. Remove these bolts. The bumper should come off.
For more details, click here at https://www.drivenbystyle.com/body-kits-aerodynamics/front-bumpers

For front bumper removal,i suggest you to click the link below :---How to Replace Front Bumper? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-front-bumper-on-audi-a4.html
-------How to Attach the front bumper cover to the fender? http://technoanswers.blogspot.com/2012/01/how-to-attach-front-bumper-cover-to.html

-----------------

This will help.

Thanks.

Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.

Becareful not to damage the fog lamp harness upon removal

Front

1. Note the radio security code, then disconnect the negative battery cable.
   
2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
   
3. On V6 Odyssey models, perform the following:
   
   • Remove the grille.
     
   • Remove the pins and clips from the lower front of the bumper.
     
4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
   
5. Pull the ends of the bumper outward.
   
6. Have an assistant help guide the bumper up and away from the vehicle.
   
7. Installation is the reverse of the removal procedure.
   

have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal

1. Raise and support the vehicle.
   

1. Remove the RH and LH front wheel (1007).
   

1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).
   
   
   
   
   

1. Remove the four front fender brace screws.
   
   
   
   
   

1. Remove the two front fender brace nuts.
   

1. Remove the two plastic screws.
   

1. Remove the seven clip buttons located under the front bumper cover (17D957).
   
   
   
   
   

1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
   

1. Remove the four front bumper cover brace bolts.
   
   
   
   
   

1. Remove the front bumper cover from the vehicle.
   
   
   
   
   

1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).
   
   
   
   
2. Remove the eight front bumper bolts.

1. Remove the front bumper from the vehicle.
   

Front Bumper (434230)

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.

1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
3. You will also need to remove some of the fasteners at the front of the inner wheel well.
4. The Front Bumper Fascia is the plastic cover over your front bumper.
   
5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.
   

remove front bumper and it should be clear what holding the face skid in place