Cruise control stopped working

DIAGNOSIS REQUIRED. CALL (517) 489-1566 BRING TO AUTOWORX W. LANSING. I AM THE OWNER JEFF

there will be a cable from the cruise control that moves when the cruise controls the car. This cable is usually paralleled to the cable that the accelerator pedal moves.At the throttle control of the engine you will find these wire cables. If the cruise control cable is not oiled it can seize in the cable sleeve which might affect the accelerator pedal also.

On these case,to troubleshoot these problem,there are solved help links.Click the link directly and refer the details to solve these problem yourself,with help of diagrams:------
Ford ranger cruise control not working?

http://technoanswers.blogspot.in/2012/02/ford-ranger-cruise-control-not-working.html

----------- Horn and Cruise control quit working?

http://howtobyme.blogspot.com/2011/11/horn-and-cruise-control-quit-working.html

--------

Horn and cruise control not working on Plymouth Grand Voyager?

http://howtobyme.blogspot.com/2011/11/horn-and-cruise-control-not-working-on.html

------------------
Horn and Cruise control quit working on 2003 Jaguar S-Type? http://howtobyme.blogspot.com/2011/11/horn-and-cruise-control-quit-working-on.html

-------------
Cruise Control stops working, Excessive cranks to start the engine and RPM goes max 2500 http://whoisbyme.blogspot.in/2012/07/cruise-control-stops-workingexcessive.html

----------
Cruise control stop working on 1994 Ford ranger? http://technoanswers.blogspot.in/2012/02/cruise-control-stop-working-on-1994.html

----------
Cruise control not working? http://schematicsdiagram.blogspot.com/2011/12/cruise-control-not-working.html

--------------
1996 Ford Explorer: Cruise Control Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/1996-ford-explorer-cruise-control.html
----------
These will help.
Thanks.

Cruise controls can cease to engage if the clutch or brake light cruise switch are out of adjustment. If this happens, try placing you foot under the clutch pedal (if equipped) and lift up on it (toward you) and hold it while engaging the cruise. If it now works, it will likely cut out when you remove your foot from under the pedal. Check the brake pedal in an identical fashion. Adjusting the switch at the pedals can often solve he problem. Some vehicles (Honda, Acura, Ford, to name a few) have a plastic insert that mounts in the pedal arm which presses against the switch. These can become brittle and fracture into pieces. My Acura has little pieces of blue plastic on the floorboard around the brake pedal one afternoon and I noticed the cruise didn't work. It was the pieces of the insert that had come to pieces preventing the cruise from coming on. I replaced the insert and no more problem with the cruise.

Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .
Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

check for power supplies and brake fluid level. if to low the cruise will not work.

The cruise control suddenly stopped working and lites did not come on either, was working fine one day then next day it didnt'. Is there a fuse that might have gone out and if so where is it located?

Check to see if you have any relays. Also make sure vaccuum hose is still connected.

This works...the cruise is directly tied to the brake lights...when I replaced the brake and side light bulbs on my 2004 Santa Fe,,,the cruise started working with no other adjustments. It must complete a circuit or something.

Are you use cruise control a lot?