Gm passlock security system how to disable

You can't. It has an anti-theft device. The days of boosting a car with a couple of wires ended in the 1980s! You have to fix the problem, not find a way around it.

General Motors Vehicles Equipped with PASSLock ...

www.locksmithledger.com > keys-tools > article > gene...

The PassLock system was designed to prevent vehicle theft by disabling fuel to the engine if ... Chevrolet Silverado 1997-2004. Chevrolet Sport Van 1997-2000

CHEVY EXPRESS GMC SAVANNA VAN 2500 3500 ANTI ...

www.ebay.ca > ... > Other

REBUILT WITH LIFETIME WARRANTY GM Passlock Anti-Theft VATS module. PART NUMBER 16264985. THIS PART IS OBSOLETE AND UNAVAILABLE AT ... Rating: 5 · ‎2 reviews · ‎US$149.99 · ‎In stock

16264975 GM Passlock Chevy Express GMC ... - Amazon.com

www.amazon.com > 16264975-Passlock-Express-Anti-...

Buy 16264975 GM Passlock Chevy Express GMC Savanna Van C3500 Anti-Theft Vats Security Module REBUILT: Anti-Theft - Amazon.com ? FREE DELIVERY ...

How to Disable a GM PassLock System

1. Leave the ignition key turned to the "On" position after the vehicle has stalled and will not start.
2. Look at the dashboard and locate the theft system light. ...
3. Turn the ignition to the "Off" position to disable the PassLock system, and wait for 20 seconds for the system to reset.
4. Start the vehicle.

If you mean the "passlock security system" then here is how it is done. Click the link. How To Permanently Disable GM PassLock System

Take the ignition switch out, and look to see if the contacts are discolored. If so, shine them up with some fine steel wool. Then it should work fine. Gm products are known for this! God-Bless you and your family! The contacts are where the wires are connected. This is for an impala but it should work on all GM vehicles.

it could be the passlock system ( anti theft system ). heres how to find out. all gm vehicles from 97-2005 contain an anti theft system called the passlock. on chevy malibu turn key on, let it stay on for 10 to 15 minutes. then turn ignition off, take out key from ignition, after 1 minute start the car. thats if its whats wrong. if this is your problem you can disable system for good ! go to www.tubesound.com/passlocksystem hope this helps,

I am assuming the light you are talking about is the "SECURITY" light on the dash. Your Alero is equipped with GM's Passlock system which cuts fuel to your engine if it determines that a source other than the key is trying to start the car.

I found this online, i posted it somewhere else as well and heard it would work...goodluck

PASSLOCK I or II DISABLEMENT
The following is a procedure to disable Passlock I or II Systems for vehicles in which remote start/stop system installations are required. This procedure is required because a remote start system will not function with the current Theft Deterrent System (Passlock) which is included on many 1996 and up GM vehicles.

Please note that this modification is intended to be used only in conjunction with the installation of a remote start/stop system and does not provide a procedure to install a remote start/stop system.

CAUSE
If an attempt is made to start a vehicle by a means other than a key rotation in the ignition switch, the Body Control Module (BCM) will interpret this start as a vehicle theft and disable the fuel injectors.

CORRECTION
A minor wiring modification may be made to allow the vehicle to be started remotely. This modification includes adding a switch to allow the customer to select "ON" to disable Passlock or "OFF" for normal Passlock operation.

CAUTION: When this modification is performed and the switch is set to the ON position, the theft deterrent feature will be disabled. When the theft deterrent is disabled the SECURITY or THEFT telltale will light up indicating that the theft deterrent system is NOT functioning.

PASSLOCK MODIFICATION
Refer to appropriate GM service manuals and/or SVMQP Electrical Guideline Manual for instruction on splicing and electrical connections.
1. Select a suitable on-off switch (see note below) which will be used to disable/enable the Passlock System. Mount the switch in a location such that it is accessible to the driver and will not interfere with normal vehicle operation.
NOTE: This is an extremely low current circuit (approx. 7mA), it is therefore very important that a high quality, low energy, fast acting switch be utilized for this application.
2. Turn the ignition switch to the OFF position.
3. Locate the Main Ignition Switch Harness in the Column. GM's Passlock System wires exit the Ignition Switch Tumbler together and then join with the Main Ignition Switch Harness. (See http://www.bulldogsecurity.com/ or http://64.85.6.118/diagrams/diagrams.asp and select your Make, Model and Year for wire colors and clues on the quickest way to access these wires.)
4. Locate the Yellow Passlock Data Wire which is included in a bundle of three tiny (20 GA) wires wrapped in friction tape.
Cut this wire and splice a 0.5mm2 (20 GA) yellow wire to each end of the cut wire.
Keep wire length to a minimum. Route modification wires clear of moving parts.
Connect the yellow wires to the switch such that the contacts are OPEN when the switch is in the ON position.
5. Turn modification switch to the OFF postion (contacts closed).
6. Start vehicle to verify normal operation. If engine "cranks but will not start" recheck the switch position (contacts should be closed), wire connectors and modification wiring.

SWITCH OPERATION
To enable remote start:
Start the engine with the ignition key (modification switch must be in the OFF position). Turn modification switch to the ON position (contacts open). The SECURITY or THEFT telltale will light up indicating that the Passlock System is inoperative.Once the SECURITY or THEFT telltale has been on for at least 5 seconds the vehicle can be turned off and then remotely started.

To disable remote start:
The Passlock System can be reactivated by turning the modification switch OFF (contacts closed). Vehicle can either be running or off when this is done.

Please note that the VCM/PCM will record Diagnostic Trouble Codes (DTCs) related to the security system when the modification switch is in the ON position (circuit open). This is due to the way that the VCM/PCM interprets this condition.

NOTICE
Any condition which removes battery power from the Vehicle Control Module/Powertrain Control Module (VCM/PCM) (e.g. dead battery, disconnected harness connectors, etc.) will prevent the vehicle from being restarted. If the engine exhibits a "cranks but will not start" symptom, place the modification switch in the OFF (contacts closed) position. This will reactivate the Passlock System and allow the vehicle to be started with the ignition key.

Hope helps (remember to rate and comment this).

to disable theft system or passlock. if you have a computer go to tubesound.com for instructions on fixing problem. when on page, type in problem on the top of page. this page will tell ya how to disable system. tubesound.com/passlock system. disables passlock system for good. all gm to date,

Passlock I reset.

1. Attempt to start the car, let it stall, but DO NOT turn the key off! Leave it in RUN.
2. Wait 10 minutes or until the Theft Sys light glows steady instead of blinking.
3. Do not turn the key off, but start it immediately.
4. This should reset your Passlock system.




PASSLOCK I or II DISABLEMENT

The following is a procedure to disable Passlock I or II Systems for vehicles
in which remote start/stop system installations are required. This procedure
is required because a remote start system will not function with the current
Theft Deterrent System (Passlock) which is included on many 1996 and up GM
vehicles.

Please note that this modification is intended to be used only in conjunction
with the installation of a remote start/stop system and does not provide a
procedure to install a remote start/stop system.

CAUSE
If an attempt is made to start a vehicle by a means other than a key rotation
in the ignition switch, the Body Control Module (BCM) will interpret this
start as a vehicle theft and disable the fuel injectors.

CORRECTION
A minor wiring modification may be made to allow the vehicle to be started
remotely. This modification includes adding a switch to allow the customer to
select ?ON? to allow remote starting or ?OFF? for normal Passlock operation.

CAUTION: When this modification is performed and the switch is set to the ON
position, the theft deterrent feature will be disabled. When the theft
deterrent is disabled the SECURITY/THEFT SYSTEM telltale will light up
indicating that the theft deterrent system is NOT functioning.

PASSLOCK MODIFICATION
Refer to appropriate GM service manuals and/or SVMQP Electrical Guideline
Manual for instruction on splicing and electrical connections.
1. Select a suitable on-off switch (see note below) which will be used to
disable/
enable the Passlock System. Mount the switch in a location such that it is
accessible to the driver and will not interfere with normal vehicle operation.


NOTE: This is an extremely low current circuit (approx. 7mA), it is therefore
very important that a high quality, low energy, fast acting switch be
utilized for this application.
2. Turn the ignition switch to the OFF position.
3. Locate the Main Ignition Switch Harness in the Column. GM's Passlock
System wires exit the Ignition Switch Tumbler together and then join with the
Main Ignition Switch Harness. (See http://www.bulldogsecurity.com/ or
http://64.85.6.118/diagrams/diagrams.asp and select your Make, Model and
Year for wire colors and clues on the quickest way to access these wires.)
4. Locate the Yellow Passlock Data Wire which is included in a bundle of
three tiny (20 GA) wires wrapped in friction tape.
Cut this wire and splice a 0.5mm2 (20 GA) yellow wire to each end of the cut
wire.
Keep wire length to a minimum. Route modification wires clear of moving parts.


Connect the yellow wires to the switch such that the contacts are OPEN when
the switch is in the ON position.
5. Turn modification switch to the OFF postion (contacts closed).
6. Start vehicle to verify normal operation. If engine ?cranks but will not
start"
recheck the switch position (contacts should be closed), wire connectors and
modification wiring.

SWITCH OPERATION

To enable remote start:
Start the engine with the ignition key (modification switch must be in the
OFF
position). Turn modification switch to the ON position (contacts open). The
SECURITY/THEFT SYSTEM Telltale will light up indicating that the Passlock
System is inoperative.
Once the SECURITY/THEFT SYSTEM telltale has been on for at least 5 seconds
the vehicle can be turned off and then remotely started.

To disable remote start:
The Passlock System can be reactivated by turning the modification switch OFF
(contacts closed). Vehicle can either be running or off when this is done.

Please note that the VCM/PCM will record Diagnostic Trouble Codes (DTCs)
related to the security system when the modification switch is in the ON
position (circuit open). This is due to the way that the VCM/PCM interprets
this condition.

NOTICE
Any condition which removes battery power from the Vehicle Control
Module/Powertrain Control Module (VCM/PCM) (e.g. dead battery, disconnected
harness connectors, etc.) will prevent the vehicle from being restarted. If
the engine exhibits a ?cranks but will not start? symptom, place the
modification switch in the OFF (contacts closed) position. This will
reactivate the Passlock System and allow the vehicle to be started with the
ignition key

Unfortunately you are correct, this
vehicle has the PASSLOCK II key
based engine disabling system, and currently it
is engaged. The sensor does not recognize &
retain the passlock reader chip in your ignition
switch any longer.

A bypass is required to circumvent.
If left unchecked, it will lock down the fuel injector
rail (as it has now), and you will need to
tow it in to GM for evaluation, and resetting.
Eventuall, the 10 minute over ride will cease to
work and you will finally be forced to visit
a Pontiac/GM dealer.

But, if you want to just remove this system
from the equation entirelly,
I suggest the PLJX bypass kit to get around
this issue.

This Passlock Bypass Module is designed to momentarilly
allow the engine to remote start by sending a proper
coded pulse to open the fuel rail passlock injector
cut off circuit.

The output from an alarm/remote starter
would then shut down the pulse, once it has detected
the engine has engaged, and preserve the integrity
of the passlock system.

That is it's designed purpose.

However, in your case, this input wire on the PLJX module,
instead of going to a momentary ground pulse from
an alarm/remote starter,
would go to a constant chassis ground, through
the bypass module, grounding out the PASSLOCK.
The PASSLOCK would then always be bypassed as long
as that wire is chassis grounded.

I can not speak about a damaged passlock system,
like if a thief has destroyed it, because I do not
get into this part of GM'S security application.
Coincidence to installing
after market remote starters, this does work on bypassing
passlock in most all GM vehicles,
including your year GM vehicle as well.

Also, this is a self learning, resistor sensing
and adjusting module. Once the VATS wires have been tapped,
you would press the program button to learn,
and it does. The car should then allow start
with any hardware store key.