2005 Jeep Grand Cherokee Logo
Posted on May 02, 2009

Need to remove head rest to put on seat covers

How do I remove the head rest to put on a seat cover

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on May 04, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: May 01, 2009
Answers
1
Questions
1
Helped
1062
Points
2

I looked into new headrest for my 2005 Grand Cherokee with the monitors installed in them. I had mine off but couldn't remember how i did it. But I got the instuctions from the the company with the new headrest and they linked me to a video online. The company was on ebay. I remember that it was really simple

2 Related Answers

wfservices

Wayne Fellows

  • 262 Answers
  • Posted on Aug 21, 2010

SOURCE: We need to remove the

Head Restraints Removal

  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Ad
ourhowse

Dar

  • 2007 Answers
  • Posted on Dec 27, 2009

SOURCE: 07 Expedition second row seat head rest cover plate removal

There should either be a little button at the base of the headrest that you push, or a small hole in the rod part, with a hole in it. Push in the hole with a pen, or a small nail to release the headrest.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Remove front head rests for 2015 Dodge Journey to put seat covers on

Headrests are part of airbag system and solidly attached to seat back. They do not pull out. You will need a two piece seat cover
0helpful
1answer
0helpful
1answer

How to remove headrests on 2010 grand caravan

lift the head rest there is a tad that the head rest slide in squeeze the tad and pull up on the head rest.
0helpful
2answers

How to remove the headrests to put seat covers on for a 1989 crown victoria?

90% of head rests just pull out. the others will have a button where the headrest goes into the seat. If yours doesn't have the button, then push the headrest down and **** it up with some force and it will come out. Just be carefull you don't hit yourself in the face with it. Been there done that
0helpful
1answer

Hi how to take off vinyl covers seats on alfa romeo spider 86

IIRC......Remove seat.

Remove rear seat cover by sliding down after removing Phillips screws at bottom.

Inside you will see bolts holding seat head rests to seat.

Under seat are Hog Rings holding seat cover to frame.
.
2helpful
1answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?

Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif
0helpful
1answer

How do you remove head rest to put seat cover on ?

I think there are two screws one on each side after you raise the head rest take out the screws then the head rest should slide off
1helpful
1answer

07 Expedition second row seat head rest cover plate removal

There should either be a little button at the base of the headrest that you push, or a small hole in the rod part, with a hole in it. Push in the hole with a pen, or a small nail to release the headrest.
0helpful
1answer

1994 BMW head rest

there should be a sliding button just where the pole of the headrest goes into the seat, just push this , and the headrest should come out
0helpful
1answer

Take seat cover off

You need to remove the seat from the floor. Take out of the car and turn it upside down. Remove the hog rings holding the cover to the frame and remove the cover. Do your patch/repair and put the cover back on. Before you start, get a box of hog-rings and a pair of hog-ring pliers to crimp them with back in the same holes you removed them from. As for the head rest, there should be a button on the side to release it. Then just pull it straight up.
Not finding what you are looking for?

1,072 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...