On climate control press off and heat button and let go quickly. Then press automatic. The display will start rotating eventually displaying a code 025,125 , 024 etc. Then press defrost to stop. You may hear blend door operating atb that time. It worked for my climate control.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Temperature Blend Door Actuators
The dual-zone EATC system uses 2 temperature blend door actuators to control 2 separate temperature blend doors. The temperature blend doors independently vary the LH side and RH side temperature settings, as desired. The temperature blend door actuators each contain a reversible electric motor and a potentiometer. The potentiometer circuit consists of a 5-volt reference signal connected to one end of a variable resistor, and a signal ground connected to the other. A signal return circuit is connected to a contact wiper, which is driven along the variable resistor by the actuator shaft. The signal returned to the EATC module from the contact wiper indicates the position of the temperature blend door. The EATC module drives the actuator motor in whichever direction is necessary to make the actuator contact wiper voltage agree with the expected EATC module contact wiper voltage value.
Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH
Removal and Installation NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding. LH temperature blend door actuator and linkage
Remove the 2 lower steering column opening cover bolts.
Detach the lower steering column opening cover.
Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
Position the instrument panel wire harness away from the LH temperature blend door actuator.
Remove the 3 LH temperature blend door actuator screws.
Disconnect the LH temperature blend door actuator electrical connector.
Remove the LH temperature blend door actuator.
Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC
Removal and Installation NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding. RH temperature blend door actuator and linkage
Disconnect the glove compartment damper from the glove compartment.
Remove the glove compartment.
Remove the RH lower instrument panel insulator.
Remove the RH lower floor console trim panel.
Remove the 3 RH temperature blend door actuator screws.
Disconnect the RH temperature blend door actuator electrical connector.
Remove the RH temperature blend door actuator.
Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
Mode Door Actuator - Defrost/Panel/Floor Door
Removal and Installation NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel. NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding. Mode door actuator and linkage
Remove the 3 defrost/panel/floor mode door actuator screws.
Disconnect the defrost/panel/floor mode door actuator electrical connector.
Remove the defrost/panel/floor mode door actuator.
Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
Mode door actuator linkage only
Remove the mode door linkage.
Depress the tab and remove the panel door lever.
Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
Pull straight outward to remove the floor/defrost door lever.
Mode door actuator and linkage
NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
To install, reverse the removal procedure.
Your dual climate control is either out of synchronization or the system has a stuck air temperature blend door in duct due to heat warping and or blend door actuator drive motor has failed. It really takes a dealer to decide which is the problem by using a special scanner.
Hi there: Error Code 24 - AC/Heater Air Temperature Control Blend Door failure If it comes up 24 or 25 it is the blend door actuaton, or the shaft on the door is stuck (rust). Basically, there's a small geared electic motor that controls the blend door position of the hot/cold blend of air; keep in mind that this device is called an actuator and it breaks.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
The heater and a/c blend door actuator motor is located behind the center of the dash just below the windshield. The steering column must be detached and lowered and the dash must be removed to access the blend door motor.
can you turn pin to line it up?
blend door actuator
×