Question about Cars & Trucks

1 Answer

No electrical supply to crank the car - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 122 Answers

Try jump starting or replacing the battery. Could be a symptom of an electrical issue or alternator problem.

Posted on Nov 05, 2013

Testimonial: "I tried jump will not have any light on.bought a new battery all lights still blank"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 Chevrolet Uplander 3.5 has no crank, no start, no lights on dash board only engine lights, no radio what do I need to do?


Do you know how to do automotive electrical testing , with a volt meter . Check out videos on youtube basic automotive electrical testing . Do you have a scan tool ? That would be a good first step . Do you have any idea how many elctronic control modules are on your vehicle ? Do you know what a serial data communication network is . C.A.N How to Diagnose Controller Area Network CAN When you turn the key to start do you know what happens ?

Circuit Description (Key Start)
For ignition switch power modes refer to Body Control System Description and Operation . When the ignition switch is placed in the Start position a discrete signal is supplied to the body control module (BCM) notifying it that the ignition is in the Start position. The BCM then sends a message to the powertrain control module (PCM)/engine control module (ECM) notifying it that CRANK has been requested. At the same time the BCM is supplying 12 volts for the IGN 1 relay closing it and supplying battery positive voltage for the crank relay coil. The PCM/ECM verifies that the transmission is in Park or Neutral. If it is, the PCM/ECM grounds the control circuit of the crank relay. When this occurs battery positive voltage is supplied through the switch side of the crank relay to the S terminal of the starter solenoid.

What you need to do is have it towed to the dealer !

Mar 07, 2017 | Chevrolet Cars & Trucks

1 Answer

Someone tried to hotwire my ford demolished the ignition how do i crank it until i get it repaired


Depends on the year. Older ones have an electric relay supplying 12v to the starter solenoid. A wire jumper from batter + to the non grounded relay coil connection will crank the motor

May 14, 2016 | Ford Cars & Trucks

1 Answer

TATA INDIGO FUEL PUMP current problem


at my yahoo message not support the vido call

Dec 18, 2013 | Cars & Trucks

1 Answer

Crank but doesnt start


U must perform tracking diagnostic.Ceck spark (if u know how,by sparkplug plug and a wire close to grounded part,whatch for electrical shoque,must use gloves)Ceck fuel supply (u can supply fuel directly to see if sttarts).Last:Bad timing.

Oct 22, 2013 | 1992 Chrysler Town & Country

2 Answers

Is it the battery or the alternator


All the battery does is supply power to the starter to crank the engine over. The alternator doesn't start working until after the engine is started. It supplies electrical power to the engine after it has started and also recharges the battery. If the engine is cranking over but not starting it is neither the alternator or the battery. Check for spark and fuel pressure your most likely missing one of these.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Aug 07, 2012 | 2003 Oldsmobile Alero

1 Answer

Replaced ther battery and now the engine turns over but it will not crank


first check the supply from fuel pump,most probably the fuel pump problem disconnected or filter ,if not check electrically spark plugs by removing one and turn engine if spark come on so no problem electrically.

Mar 23, 2011 | 2003 Mitsubishi Outlander

1 Answer

Dash door and brake warning lights on; car won'tstart; seems like no gass.


There is an ECM to control the starting and running of the engine but it seldom is the problem.

First you need to isolate if it is mechanical, electrical or fuel that is causing the problem.

Remove the distributor cap and crank the engine, if the rotor turns, we can skip mechanical.

Before checking any electricals, check if there are any blown fuses both under dash and hood.

Check for power supply to distributor Black/Yellow wire with ignition switch on. If there is, pull 1 plug wire out and insert a plug to its end and ground it on the engine, NEVER groud it to the battery terminals.

Crank the engine and if you see blue sparks it is ok, reddish or yellow sparks means the coils is bad.

If no sparks, the ICM is faulty.

Test for power supply to fuel pump at initial ignition switch turned on, (2 seconds only) and while cranking. If none, the main relay is faulty.


Take care

Oct 09, 2010 | 1999 Honda Accord

1 Answer

95 toyota tercle will not start


1. check the battery if its charged or not by blowing the horn.
2. if the battery is ok try crank the engine if it doesnt crank then you have a starter problem.
3. after you crank the engine check if you have enough fuel on your tank.
4. if it wont start check the ignition system for electrical supply on your spark plugs and if everything fails you got to let a mechanic check your car.

Apr 07, 2010 | 1995 Toyota Tercel

1 Answer

B200, 2006 cvt trany,starter doe,s not crank at all every once in a while, battery ok, connections et ground ok. the scanner tell,s us starter is defect. I dont have a wiring diagram so i have to figure...


You can electrical supply directly from plus battery to electrical starter solenoid.
For that you must prepar an electrical wire. One end connected at the electrical starter solenoid, and another end directly on plus battery. If electrical starter crancks the problem is on electrical supply. If doesn't cranks then electrical starter
is out of order and must be removed from engine and repaired! The most frequent problem of electric starters are carbon brushes used!
Did you try this operation?

Jan 14, 2010 | 2006 Mercedes-Benz B-Class

1 Answer

2000 dodge stratus problem


crank sensor???? it might have a short in the 5 volt power supply. crank sensors can confuse the computor to thinking its the cam sensor. good luck

Sep 20, 2008 | 2001 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

84619 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

20167 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...