2006 chevy malibu: interior lights not coming on with doors opening, but does come on if I switch it on with the toggle at dome lamp

The door switch doesn't go to the dome lights , the switch (door ajar switch ) is an input to the SMJ - smart junction box or body control module take your pick .
Principles of Operation
When the SJB detects a request for lighting, it turns on the interior lamps by supplying power to the lamps. The request for lighting can be an open door signal from a door ajar switch, an interior lighting on command from the instrument panel dimmer switch or an unlock command from a remote keyless entry (RKE) transmitter.
The door ajar switches are hard-wired directly to the SJB. The 2 door ajar switches are normally closed when the doors are closed. The decklid ajar switch is normally closed when the decklid is closed. All door ajar switches receive voltage from the SJB and each has its own ground circuit.
The instrument panel dimmer switch receives a ground signal from the SJB. The instrument panel dimmer switch provides variable resistance for backlighting the instrument cluster and a toggle ON/OFF function for the interior lights.
The RKE receiver is contained inside the SJB. When the SJB receives an unlock request from an RKE transmitter, it unlocks the doors and turns on the interior lamps. There could be DTC'S diagnostic trouble codes stored in the SJB ! You can not access these codes with a OBD2 code reader , need a factory scan tool .
B1319 Driver Door Ajar Circuit Failure Go To Pinpoint Test D . B1327 Passenger Door Ajar Circuit Failure Go To Pinpoint Test D . B2021 Dome Lamp Input Return Circuit Failure Go To Pinpoint Test A . B2550 Dome Lamp Output Circuit Short to Ground Go To Pinpoint Test A . B2554 Dome Lamp Output Circuit Failure Go To Pinpoint Test D . Do you know B-codes -body control .
Your best bet is to take to a ASE certified repair facility or a Ford dealer .

Search Results

No interior lights with door open - Tahoe Forum - Chevy Tahoe Forum

tahoeforum.com/showthread.php?p=654123

Feb 5, 2013 - 10 posts - ‎6 authors
Interior dome lights don't come on when I open any of the doors. ... 02-06-2013,03:11 PM, #2 ... Make sure to have the interial light all the way just before it clicks to ... But I would push it until the lights come on when you open your door. ... Zigger21 (Jonathan) - Thx. That was the first thing I tried after my wife ...

Why don't my doors activate my dome lights ... - CarGurus

www.cargurus.com > Questions > Chevrolet > Silverado 1500

CarGurusDec 23, 2014 - My dome lights work, but the doors when opened will not operate these ... 2014 at 03:15 AM about the 2008 Chevrolet Silverado 1500 Work ... In my chevy Tahoe the fix was simple. ... That's the on and off control for the dome lights.look carefully you will ... Dome light doesn't come on but it dings every bump.

Dome lights wont come on - Chevrolet Forum - Chevy Enthu

The courtesy lamp supply voltage circuit of the body control module (BCM) supplies battery positive voltage to the dome lamp, the liftgate lamps, and the map lamps. When any door is opened, the door jamb switch contacts close providing a door open input to the BCM. The BCM then provides a ground to the interior lamps with the switch in the AUTO position. The interior lamps receive a ground at G401 with the switch in the ON position.
The following lamps may be manually turned ON by placing the interior lamp switch in the ON position, or by opening a door while the switch is in the AUTO position.
?€¢
The dome lamp

?€¢
The liftgate lamps

?€¢
Courtesy/map lights

You can't turn them on manually ?
This could be a BCM problem , this best left to a ASE certified repair shop or the dealer .

The following lamps may be manually turned ON by placing the interior lamp switch in the ON position, or by opening a door while the switch is in the AUTO position.
?€¢
The dome lamp

?€¢
The liftgate lamps

?€¢
Courtesy/map lights

The courtesy lamp supply voltage circuit of the body control module (BCM) supplies battery positive voltage to the dome lamp, the liftgate lamps, and the map lamps. When any door is opened, the door jamb switch contacts close providing a door open input to the BCM. The BCM then provides a ground to the interior lamps with the switch in the AUTO position. The interior lamps receive a ground at G401 with the switch in the ON position.
Important: If the liftgate is opened after all the modules go to sleep, the dome light will not come on. The liftgate ajar switch input to the BCM will not wake up the BCM once it has gone to sleep, so the dome light will not come on. Once the BCM gets an input to wake it up, from remote keyless entry (RKE) or a door handle, the dome light will turn on when the liftgate is opened.
If the driver inadvertently leaves any interior lamp ON, the BCM will turn it OFF after a 20 minute time-out.
The courtesy lamps will turn OFF immediately if the ignition switch is turned to the ON position or approximately 20 seconds after all doors are closed.
The courtesy lamps are controlled by the body control module (BCM). Inputs from the dome lamp switch and the door ajar switches are monitored by the BCM. When a door ajar switch is closed, or the dome lamp switch is turned to the ON position, the BCM supplies the B+ for the courtesy lamps.
With out a factory Tech2 scan tool or equivalent an knowing how these systems work ,you best bet is to take your vehicle to the dealer or some other ASE certified repair shop !

the chime actually is done with the radio. the front drivers door speaker. so if the radio works and the front left speaker works. then more then likely you have a defective door switch. located in the door jam that controls the dome light

its either a bad door switch,or could be the dome override switch by headlight switch,or your interior light switch is all the way up

all the lights above the dash do not work ?????? DOME light's ??? No light's come on when you open the door or any door ? Wouldn't think all the door ajar switches bad at one time .
Interior Lamps
The interior lamps consists of two groups, lamps that can not be dimmed and lamps that can be dimmed. This first group consists of lamps that may not be dimmed. This Includes those lamps that may be manually turned on by placing the interior lamp switch to the DOME position, or by opening a door or a compartment:
• Auxiliary dome lamp (SEO, RPO 6C7)
• Dome lamp
• instrument panel (I/P) compartment lamp
• Inside rear view mirror lamps
• I/P courtesy lamps
• Reading lamps
• Rear compartment courtesy lamp
• Sunshade vanity mirror lamps
Battery positive voltage is applied at all times to the DIC/RKE fuse and to the switched side of the BATT RUNDOWN PROTECTION relay in the right I/P junction block. The DIC/RKE fuse supplies battery positive voltage to the coil side of the BATT RUNDOWN PROTECTION relay. When the ignition is turned to the ON position, the body control module (BCM) provides a ground to the Inadvertent relay control circuit. This energizes the BATT RUNDOWN PROTECTION relay and applies battery positive voltage to I/P BRP fuse and to the TRK/ROOF/BRP fuse. Battery positive voltage is applied from the I/P BRP fuse to the I/P courtesy lamps, I/P compartment lamp and to the I/P compartment feed circuit to the BCM. Battery positive voltage is also applied from the TRK/ROOF/BRP fuse to the:

If the BCM receives a door lock or unlock input signal, the BCM will activate the BATT RUNDOWN PROTECTION relay, which provides battery positive voltage to all interior courtesy lamps. When any door is opened, the door jam switch contacts close and the BCM receives a door-open input signal. The BCM then applies a ground to the theater dimming ground control circuit illuminating the courtesy and dome lamps.
After all the doors are closed, the courtesy lamps remain illuminated for approximately 40 seconds. The courtesy lamps will also turn on and remain illuminated for approximately 15 seconds after the ignition key is removed, prior to any door being opened.
When the headlamp switch is placed in the DOME position, the BCM receives a ground signal. The BCM then applies a ground to the theater dimming ground control circuit. This illuminates the dome and roof rail lamps.
The courtesy lamps will normally turn off using the theater dimming feature. The BCM provides a pulse width modulated ground to all courtesy/reading, dome, and inside rear view mirror lamps for the theater dimming feature. The BCM will immediately turn off the courtesy lamps if a door lock command is received with all the doors closed, or if the ignition switch is turned to either the ON or RUN position.
The BCM activates the interior lighting output 15 seconds after receiving the class 2 message "Airbags Deployed" from the sensing and diagnostic module (SDM). The interior lamps remain activated for 25 minutes.

The door ajar switch is part of the lock actuator inside the door !

On most vehicles, the dome light has 3 settings,
(1) on always (your manual slide you are doing)
(2) On only when door opens (or the key fob pressed)
(3) Always Off

Usually the same switch to turn on (position 1) is a 3 position switch that allows for all 3 modes. However, I have a Buick LaCrosse (I thought a sister model), and the switch for control of this is on the left side of instrument panel with the headlight controls.

Check to see if you have 3 options rather than just on or off.