Replace o2 sencer bank 1 circuit 1

If they are codes P0135 and P0155 they refer to both O2 sensors nearest the engine on the exhaust. The ones before the catalytic converter on each exhaust pipe.
P0135 = O2 Sensor Heater Circuit Bank 1 Sensor 1
P0155 = O2 Sensor Heater Circuit Bank 2 Sensor 1

code p 420 refers to cat converter system , bank 1--efficiency below threshold ===causes ---cat converter faulty---wiring --heated oxygen sensor (HO2S), 2 faulty
code p 0134 refers to HO2S 1 bank 1-no activity detected ===causes --wiring open circuit -- heating inoperative --- HO2S
also refers to oxygen sensor ( O2S) 1 bank 1--no activity detected == causes wiring ---O2S
code p 0138 refers to HO2S 2 bank 1--high voltage === causes ---wiring short to positive ---HO2S--- ECM
also refers to O2S 2 bank 1 high voltage === wiring short to positive O2S -- ECM
I do not have a listing for code p 1338 but I suspect that it will refer to the other codes in some way
first fix is to check the cat converter is operational ( not cracked and blocking the exhaust system)
next replace the HO2S sensor ( one before the cat converter ) and then the O2 sensor (the one after the cat converter)
all the codes will relate to problems in that area

O2 sensors are always after the cat converter and HO2S sensors are always before the cat converter.
p0135 refers to heated oxygen sensor(HO2S) 1 bank 1-heater control--circuit malfunction
If it is a straight 6 cylinder engine with 2 cat converters it will be the sensor before the cat converter that connects to the manifold from pistons 1.2.3
If it is a V6 it will be the sensor that is in front of the cat converter that connects to the rear bank pistons 1.2.3. Use the special socket when removing/replacing the sensors to prevent wiring damage

Replace O2 sensor one in cylinder bank one.
The sensor is the one before the ca converter in the cylinder bank that contains cylinder #1 See diagram below. Please rate my help.

try the o2 sencers they are those likely to go bad usefully bank 1 sencer 1 just before your cat converter

Oxygen Sensor problems... P0135 (Bank 1, Sensor 1) and P0141 (Bank 1, Sensor 2)

P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it.

The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0135 may mean that one or more of the following has happened:
O2 Heater element resistance is high
Internal short or open in the heater element
O2 heater circuit wiring high resistance
open or short to ground in the wiring harness

Possible Solutions:
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)



P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
This code means that the heated circuit in the oxygen sensor on bank 1 decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0141.

Symptoms: You will likely notice poor fuel economy the illumination of the Check Engine Light.

Causes: A code P0141 may mean that one or more of the following has happened:
open or short to ground in the wiring harness
O2 heater circuit wiring high resistance
O2 heater element resistance is high
Internal short or open in the heater element

Note: Typically a failed catalytic converter does not cause this code. You're more likely to see a P0420 code for a failed converter.

Possible Solutions:
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)
Repair short or open or high resistance in wiring harness or harness connectors


Hope this helps (remember to rate this answer)..

Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).

Bank 2 sensor 1 Air fuel sensor heater circuit. This sensor is NOT an O2 sensor, though it operates like one and in the same location(in exhaust stream). Basically the PCM detected that the heater circuit was drawing excessive amperage or no amperage. Usually it's a bad a/f sensor and replacing it will fix it, however, it doesn't rule out the possibility of damaged wiring or an open in the power or ground circuit, or a short in the power or ground circuit.

Hope helps (remember rated this).

Hi.

P0032 means HO2S Heater Control Circuit High (Bank 1 Sensor 1).

It means high impedance from O2 sensor, check wiring to sensor and replace the sensor.
Check O2 sensor located in bank 1 (cylinder 1 side- see here), and after the catalitic converter (there is also an O2 sensor before cat converter).

I believe your car only has a single catalytic converter. If that's the case, then your bank 1 sensor 2 will be the O2 sensor that's located after the Catalytic converter away from the engine