Question about Toyota Cars & Trucks

1 Answer

I have a 2005 toyota tundra v8 and when i put the truck in reverse and drive it, it squeeks. but if i wet the back axel and the back of the brakes it eventually goes away for a couple of days and comes back?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 843 Answers

Hi,if it has drum bracks it could be brack dust inside the drum,if its disk bracks they might need copper- slick put on the brack pades,on the side that faces the brack-caliper.
hope this was some help.

Posted on Oct 29, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Wiring Issues

Thank you for allowing me to assist with your problem.
Regarding your fuse issue, there may be a couple of things to look for...the first thing that I would look for is corrosion at the wiring harness connector under the bed that feeds the rear taillamps. Salt, water intrusion and the like can cause these contacts to oxidize, and the oxidation can spread across the teminals, shorting out to the ground wire in the same connector. Most noticible in the "snow-belt" states, or if you put boats in water. Check for corrosion in this connector, if it is OK, please get back to me for other info.

Posted on Oct 06, 2008

  • 1 Answer

SOURCE: how much oil do i put in a 4.7l V8 toyota tundra 06?

6.5 quarts and then check it after running it a bit and shut down for 5 minutes.

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: Toyota Tundra 2005. ABS, Airbag, Tire & cruise dash lights flash

how do you turn the maintenance light off after making oil change?

Posted on Sep 02, 2009

  • 1861 Answers

SOURCE: 2003 Toyota Tundra Limited Stepside truck. No Brake light

Hello.

We would suggest that you look at the wiring connector under the bed, that feeds the taillamps.

You will probably find a coroded wire in the connector. If the 3rd brake lamp works, all of the fuses and switches are good.

Posted on Dec 25, 2009

Testimonial: "All connectors were fine. It ended up being that both brake light blubs blew at the same time. Thanks"

  • 3 Answers

SOURCE: Squeaking noises when driving backwards

Check your universal joints

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Tundra access cab with V6. When you let off the gas there is a vibration that gets stronger the slower you get. It is very strong when about to stop. Does not matter if in neutral, braking or...


Suspect a drive shaft if brakes on throttle whilst braking stops it but would need a good look to have sort of idea ,and iam in spain so please consult a local mechanic

Oct 18, 2013 | 2005 Toyota Tundra SR5

1 Answer

Changed front rotors/brakes and back drums on 2006 toyota tundra front wheel drive V8, but still have pulsing during braking


Then the job either wasn't done correctly or you have
ABS System problems

You need professional tools to work on ABS

Oct 08, 2012 | Cars & Trucks

1 Answer

My 2002 toyota tundra v8 4.7l brake light burned out so i changed it out but when i press the brake it doesn't light up, how do i fix


i think the wired has a problem check the wired line that source of electricity, if has a problem change the wired line, and its working










thanks

Jun 07, 2011 | 2002 Toyota Tundra

1 Answer

Sometimes when it is cold, I put my 2001 Tundra in drive and it dont want to move, like the brakes are locked. When I put it in reverse then bump into drive everything is fine


Lift the rear tire off the ground and see if the tire rotates? if it does then your brakes are fine. Now as far as the vehicle not wanting to move right away could be due to low tranny fluid level or internal leak down.

Feb 25, 2011 | Toyota Tundra Cars & Trucks

1 Answer

I have a 2005 toyota tundra with rear parking sensor that stopped working any trouble shooting ideas?


check the fuse for that circuit.there is a beeper under the dash as well.put a test light on it and see if it flashes,that means the beeper is dead.remove the switch if there is one that turns it off and jumper across it,and check the circuit from the shifter wiring to it,and also the reverse lights,they may have it wired to the reverse lights.

Apr 26, 2010 | 2004 Toyota Tundra

1 Answer

Toyota tundra cuts off going from neutral to


The clutch lock up converter is locked,there is a solenoid that may be bad,or you need a new converter.torque converter.

Nov 12, 2009 | 2000 Toyota Tundra

1 Answer

Engine dies when put in drive


Have you checked to see if you have any codes in the engine control module ? Even if the light is not on, it will store codes which are not a major problem.

Have you done any routine maintenance to your car lately, like a tune up ? Have you checked your air filter ?

Jul 24, 2017 | 2000 Toyota Tundra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...