Keith Jones Posted on Oct 28, 2013

2002 jeep cherokee 2.5 crd replacement engine but it wont turn over can you help

1 Answer

Gavin Culley

Contributor 6 Answers
Posted on Oct 28, 2013

Gavin Culley

Contributor

Joined: Oct 28, 2013

Answers

Questions

Helped

1115

Points

Carefully put a screw driver between the live on the starter and solenoid live with the ignition on if the engine doesn't turn check your earths from battery to chassey and engine are clean and secure

5 Related Answers

Anonymous

475 Answers
Posted on Feb 24, 2009

SOURCE: 2002 Jeep Grand Cherokee Lardo misfiring

You say you changed the cam sensor. A1391 code is a crank sensor on the top of the trans. bell housing.

Vincent G

2363 Answers
Posted on Jul 15, 2009

SOURCE: 2005 DIAGNOSTIC ERROR CODE P0069, CRD ENGINE WONT

Are you traveling high ground like Rocky Mountain?

I will remove the ground cable for 4 minutes to reset all data in ECU.///clock and radio stations too : (

Let the ECU to relearn the local environment parameter.

Here's so info on how to prevent vapor lock

Ride with full tank of gas but NO TOP OFF.

Crack open gas cap carefully during rest stops to release / equalize gas tank pressure'

http://www.estes-park-information.com/vapor-lock.html

Good Luck

Anonymous

43 Answers
Posted on Aug 03, 2009

SOURCE: Very rough idle on 2002 Jeep Grand Cherokee Limited Edition V8

If you haven't changed the plugs or had the fuel system cleaned, now would be a good time to do it. The number 1 culprit for rough idles is dirty injectors or plugs. You can try an injector cleaner in a can (or bottle) for under $10 and see if it helps, and then work from there. If there isn't any improvement then if you are able to, check the plugs for any gunky buildup and if you find a bad plug, make sure you replace them all (or have them replaced) at the same time.

Anonymous

1 Answer
Posted on Aug 20, 2009

SOURCE: 2005 Jeep Grand Cherokee Limited, 5.7L V8, starter

Every morning at lunch time and evening my jeep won't start. It doesn't grind but the electrical goes crazy. After a couple of trys it finally starts. Help

Anonymous

3640 Answers
Posted on Jan 21, 2010

SOURCE: 2002 jeep grand cherokee with 4.0 engine will die but restart

p0340 is the cam shaft sensor, this will cause it to cut off while driving, hardtime starting, p0351 is the ignition coil A primary/secondary curcuit mal function. p1391 is ignition system misfire, this could be plugs, wires, or coils. first of all have the cam sensor changed and it may correct the rest of the codes. when fixed turn light off with obd2 scanner. if you do not have one, then any auto parts store will erase the codes fo free of charge.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

My 2005 Jeep Grand Cherokee stalls out and will not start?

ive seen this happen and seen 50 causes
what i the point if guessing 50 answers.
on 2 major paths of failure
wont crank
wont start but cranks ok,
is this a diesel>?
OP never said what engine is there.
wk jeep usa
wg jeep europe. 3.0 L Mercedes Benz CRD
really we are clueless to guess, what is under that hood
truly...
nor if it cranks
nor if the IMMO lamp is off
nor if fuses are good.
if gas, engine , tuned up in the last decade?

Read full answer

Jan 15, 2017 • 2005 Jeep Grand Cherokee

0helpful

1answer

Cylinder head torque specs for 2002 jeep Cherokee 2.5 crd diesel,

mitchells down>? that it?
welcome to a USA forum.
where dont have 2002 Cherokees, sorry, not a one here.
last one 2001, until 2014. so.... whats up with this post?
but they do in europe. and is our Liberty in drag.
so where are you?, tell that and helpers can look books up in
your country , we dont have this car here. so no books.
this one>?
VM Motori/Detroit Diesel

here is my wiki paste, so again, where are you.....
the crd was tried back in 80s but is not same engine,then.,

Numerous versions were available in markets outside the U.S. and Canada.
Early-2002 through mid-2003 model year CRDs were equipped with a 2.5lt VM Motori Diesel producing 105 kW (143 PS; 141 hp) and 343 N·m (253 lb·ft). An external wastegated turbo was standard and the engine was available only with a manual transmission.

and
the last North American market Jeep product that was offered witht this diesel engine was the 1987 Jeep Cherokee and Comanche.

next time post country and get 100x better answers
and faster and most important accurate.
best question would be.....????
are bolts TTY
are bolts re-useable
are bolt torqued, or angle set or both. all are the best questions.

Read full answer

Oct 22, 2016 • Jeep Cherokee Cars & Trucks

1helpful

1answer

2002 jeep Cherokee 2.5 crd cannot get engine management light to go off

Check the ASD relay ! powers injectors .Located in the engine compartment power distribution center ! ASD auto shut down relay . Very common problem .

Read full answer

Apr 18, 2016 • Jeep Cars & Trucks

1helpful

1answer

Why Engine management light wont go off after overhaul

check fuel pressure you said no fuel spray at injectors

Read full answer

Mar 23, 2016 • Cars & Trucks

0helpful

1answer

Torq settings on 3.7 cyl heads

This is the info for the 2.8d CRDI 2008-11 engine code ENS (51C)

1 Replace Head Bolts
2 Stage 1 Tighten to15 Nm
3 Stage 2 Tighten to 30 Nm
4 Stage 3 Tighten to 85deg
5 Stage 4 Tighten to 85 deg
6 Stage 5 Tighten to 85 deg

Sequence

w93gwmwpatg0gaaaabjru5erkjggg==

If it is the 01-08 model 2.8 CRD engine code R2816K4 then it is this one
Stage 1 - Bolts 1 -18 = 30 Nm
Stage 2 - Bolts 1 -10 = 75 deg
Stage 3 - Bolts 11 - 18 = 50 deg
Stage 4 - Bolts 1 - 18 - 75 deg

Sequence
aa5xdif9xa+aaaaaaelftksuqmcc