Question about 2000 Chrysler Town & Country

Open Question

Turn signal flasher location for 2000 town and country

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 2000 Town/country left turn signal

Good chance it's just a bulb problem, start there & clean socket good & replace bulb. If that doesn't cure it, get back to us.

Posted on Jun 24, 2009

Ad
  • 1779 Answers

SOURCE: MY TURN SIGNAL QUIT WORKING IS THERE A FLASHER

My service manual states that the '02 T+C has a combination turn signal/hazard flasher/daytime running lights module which is located on the junction block, adjacent to and left of the steering column. To access it, you must remove the steering column lower cover and knee pad panel. There is also a fuse for turn signal/hazard flasher. If none of them work, check the fuse 1st.

Posted on Jul 18, 2009

  • 57 Answers

SOURCE: Where is the turn signal fuse or relay located on

Under hood, drivers side, front, fuse box.

Posted on Dec 07, 2009

  • 1 Answer

SOURCE: CHRYSLER town and country mini van turn signal/flasher

I have a 2005 Chrysler T&C. The turn signal would not work at all or activate incorrect side. The switch is easy to remove as described by dukecityman.

Once the switch is of, it has four screws holding it together.I took this apart to find that there was a circuit-board which was contaminated with dirt. wiped it of, put it back together, working fine.

If you take it apart use caution. there are parts on the "top" which will fall out. ( they go right back in) The circuit-board is on the "bottom" half. You really only need to take this part off. (less moving parts)

Your going to replace it anyway, whats the harm?

Posted on Jan 28, 2010

  • 91 Answers

SOURCE: No turn signals on 1996 Chrysler town &

The turn signal flasher is worn out. The turn signals have their own flasher. It is usually on the drivers side of the vehicle under the dashboard. It is normally a cylinder about 1 inch in diameter and 1inch tall that has two prongs on it. My advice would be to go to the parts store and get a new turn signal flasher for your car. Look for something under the dash that looks like it and exchange them.

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Blinkers don't work at all. Where can I find the fuse or relay? I'm very frustrated. I need help.


Chris, fuse could be down under the dash to the left kind of near where your left knee would be when you are driving or under hood (engine compartment) in the fuse/relay center.
It could also be faulty flasher, wiring, etc
I will post some trouble shooting links for you.
Press the helpful button.
1996 2000 Chrysler Town and Country Interior Fuse Check 2000 Chrysler Town...

How To Install Replace Taillight and Bulb Chrysler Town Country 04 07...

Fuse Box Location in 1999 Plymouth Grand Voyager Van

Quick Tip Signs of blown IOD Fuse on Chrysler Dodge Jeep Fiat or Ram...


Feb 15, 2016 | 2002 Chrysler Town & Country

1 Answer

93 lincoln town car turn signal flasher location


Here's a link to what it look's like. Turn Signal Flasher 1993 Lincoln Town Car 8 Cylinders 4 6L EFI AutoZone... The Flasher is located: Front seating area, driver side, under dash, driver side of steering column, mounted on fuse side of fuse panel
Application:
Turn signal

Feb 08, 2014 | Nissan Cars & Trucks

1 Answer

Where is the fuse for the turn signals in a 1996 Chrysler Town and Country Van located?


its probly under the hood in a little black box it should say fuses if not there check under the dash on the drivers side

Oct 03, 2012 | 1996 Chrysler Town & Country

1 Answer

2000 towncar signals stopped working?


There should be a turn signal fuse in the fuse box inside the car, and there is a flasher for the hazards and one for the turn signals.
Check your owners manual for more info.

Aug 25, 2012 | 2000 Lincoln Town Car

1 Answer

My turn signals stopped working as well as the hazard lights. I replaced the fuse under the hood for the hazard lights and now they work but still nothing for the turn signals. I checked every normal (10,...


You only replace the one flasher you need to replace the turn signal one to its also located under the dash if you did that already replace your turn signal switch

Jun 27, 2011 | 2000 Chrysler Town & Country

1 Answer

Where is the turn signal/DRL module located and what does it look like


In my Haynes manual it is a combination turn signal/hazard flasher/DRL and is located in the on the junction box which is located under the dash and forward of the drivers left knee.

Feb 03, 2011 | 2001 Chrysler Town & Country

2 Answers

Emergency flashers and turn signals stop operating


The interior fuse box locations - 1995-97 Town Car 93146g31.gif
The engine compartment fuse box locations - 1995-97 Town Car 93146g30.gif
The interior fuse box locations - 1995-96 Continental 93146g34.gif
The engine compartment fuse box locations - 1995-96 Continental 93146g35.gif

Sep 24, 2010 | 1995 Lincoln Town Car

2 Answers

Where is the turn signal flasher located?


You more likely have a bulb that is no good. The next time your signals aren't working, pull over and check to see which bulb isn't working. Make sure the turn signal is on while checking. It should only be the left or right. Not both. Sometimes you can see the blown bulb with the hazards on depending on your model vehicle. Simply check the bulb thats not blinking for a tight fit. Then replace it if thats not the cure.

Apr 30, 2010 | 2006 Chrysler Town & Country

1 Answer

No turn signals on 1996 Chrysler town & country but 4 way flashers work?


The turn signal flasher is worn out. The turn signals have their own flasher. It is usually on the drivers side of the vehicle under the dashboard. It is normally a cylinder about 1 inch in diameter and 1inch tall that has two prongs on it. My advice would be to go to the parts store and get a new turn signal flasher for your car. Look for something under the dash that looks like it and exchange them.

Apr 29, 2010 | 1996 Chrysler Town & Country

1 Answer

MY TURN SIGNAL QUIT WORKING IS THERE A FLASHER


My service manual states that the '02 T+C has a combination turn signal/hazard flasher/daytime running lights module which is located on the junction block, adjacent to and left of the steering column. To access it, you must remove the steering column lower cover and knee pad panel. There is also a fuse for turn signal/hazard flasher. If none of them work, check the fuse 1st.

Jul 18, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...