1997 Dodge Avenger Anti Theft won't disarm

Hello! I hope that i will be able to help you by offering to visit this web link with big number of helpful web articles in it: https://papernow.org/

Security system does not recognize the key. Try locking the car and then unlocking with the key in the driver's door lock. If that doesn't work, try what these guys say in the link below.
Anti theft activated

do you own a slim jim to open the drivers door? if not get ahold of a tow truck driver or a police officer as they have them with them or any auto parts store sells them, once in the car psh remote button for trunk or pull down rear seat back and you are in!

Locksmith, 150 bux (vin#, id, and proof of ownership required) at the dealer or find a nice police officer with a slim jim

I’m happy to assist further over the phone at https://www.6ya.com/expert/howard_977676954994c5b2

anti theft light should blink every few seconds.

try disconnecting the battery for 15 minutes.

Anti-Theft-Perimeter The perimeter anti-theft system consists of the following components:

• anti-theft indicator (THEFT)
• remote anti-theft personality (RAP) module
• hood switch
• keyless entry remote transmitter
• deck lid ajar switch

NOTE: The remote entry features will not function when the ignition switch is in the RUN or ACC position.
Up to four keyless entry remote transmitters (15K601) can be programmed at one time.
The keyless entry remote transmitters :

• Are programmable.
• Must be set at the same time.
• House four buttons.
• House three buttons (Mexico Anti-Theft System only).

Programming
Refer to Section 501-14B.
Inputs and Outputs
The remote anti-theft personality (RAP) module receives input from the following components for anti-theft operation:

• Hood switch.
• Deck lid ajar switch.
• Keyless entry remote transmitter.
• Power door lock switches (LH and RH).
• Door courtesy input.

The RAP module distributes output to the following for the anti-theft system:

• Power door unlock relay.
• Power door lock relay.
• Liftgate unlock relay (Wagon)
• Park lamps relay.
• HORN relay.
• Dome lamp.
• THEFT indicator.
• Deck lid release.

Arming
The anti-theft system can be armed if:

• The ignition switch is in the OFF position.
• The panic alarm is off.
• All doors are closed.

NOTE: If a door is open, the anti-theft system is prearmed and waiting for all the doors to be closed. The THEFT indicator will remain illuminated for up to 30 minutes waiting for all the doors to be closed. If a door remains open after 30 minutes, the THEFT indicator will turn off and the system will return to a disarmed state. After all doors are closed and the 30 second prearm (continuous THEFT indicator illumination) is complete, the system is armed.
NOTE: If the theft LED does not flash after 30 seconds, check the LED FLASH PID to see if the feature is enabled.
The anti-theft system will be armed when the lock button on the keyless entry remote transmitter is pressed, all doors are closed and 30 seconds have elapsed.
When the system is armed, the THEFT indicator will flash quickly until the system is triggered or disarmed.
Disarming
NOTE: Using a key in a door lock cylinder to unlock is not a valid method of disarming the anti-theft system.
Untriggered System
NOTE: If the driver arms the system and remains in the vehicle, an untriggered system can be disarmed by turning the ignition switch to the ON position.
An untriggered alarm system can be disarmed by pressing the unlock button on the keyless entry remote transmitter.
Triggered System
NOTE: If the hood or trunk are open when the system is armed, it must be closed and opened again before it can trigger an alarm.
An armed anti-theft system can be triggered by the following conditions:
The deck lid door, liftgate, hood or any door is opened using a key, inside door handle, hood release, etc.

• The keyless entry remote transmitter can activate a panic alarm which is similar to the anti-theft alarm, but does not cause the THEFT indicator to flash.

A triggered alarm system can be disarmed by:

• Pressing the unlock or panic button on the keyless entry remote transmitter.
• Turning the ignition switch to the ON position.

Alarm State When Battery Power Is Cycled
When the RAP module is supplied power the first time at the vehicle assembly plant, the system will be in the disarmed state. The RAP module will remember whether it is armed, disarmed or triggered in its non-volatile memory. When the battery positive cable is removed and then reconnected, the system will return to the state it was in just before the battery was disconnected. If the system is in any prearm state, then the system will return to a disarmed state when the battery is disconnected and then reconnected.

Okay if the anti theft is really the problem the horn should be honking and some lights flashing. If i remember right to disarm the 94 intrepid you have to lock and unlock the passager side door with the key. If that dont work try driver side door and trunk all with the key. Good luck

Call AAA or CAA and get em to use a slim jim to open door, probably cost $50

Depending on where you live you can call the police and they have the tools to open the doors. If you have AAA, they have a free lockout service. If not, you can get a coat hanger and fish it carefully between the door weatherstripping. If you have anti-theft lock knob covers you can pull one up. If not you have to go for the door latch or the power lock switch if you have that. Hope this helps and it's not raining!!

The ignition lock anti-theft switch (19A438) detects if the ignition key cylinder is broken or "slam pulled" during a theft. The ignition lock anti-theft switch is always monitored by the remote anti-theft personality (RAP) module. This allows the alarm system to be triggered in the case that the ignition lock anti-theft switch detects tampering of the ignition key cylinder (even in the event that the alarm is not active at the time).
Refer to the Section 501-14B for more details on the keyless entry remote transmitter (15K601).
The door open warning lamp switch (14018) communicates to the RAP module through the generic electronic module (GEM). This input to the RAP will cause the anti-theft alarm to be sounded if the anti-theft alarm was armed.
The door disarm switches are assembled into both LH and RH lock sets. The door disarm switch must be triggered before the mechanical lock unlocks. This is to prevent the anti-theft alarm from activating when it should have been disarmed.
The RAP module controls the anti-theft system and is the brains of the keyless entry system. The RAP module communicates with the GEM to request that the interior lights be turned ON/OFF with use of the keyless entry remote transmitter, and the GEM communicates to the RAP to inform when the door is opened. Refer to Section 418-00 for inter-module communication.
The RAP module has three wire connectors attached to it:

• The antenna for the keyless entry remote transmitter.
• 26 circuit connector (C256).
• 22 circuit connector (C257).

In addition to the perimeter alarm that uses the door open warning lamp switch, the RAP module also uses the ignition lock anti-theft switch and the autolock/relock feature to prevent theft of the vehicle. For a full description of the autolock/relock system, refer to Section 501-14B .
The THEFT LED is found on the instrument panel between the tachometer scale and the needle pivot point. The LED is illuminated during prearming and flashes when armed or triggered.
Prearming and Arming the System
The system can be armed if:

• The ignition is OFF.
• The PANIC alarm is OFF.
• All doors are closed.

There are two ways to prearm the system:

• Press the LOCK button on the transmitter.
• Open a door, press the power door lock button and close the door.

After 30 seconds the system will be armed and the theft indicator in the cluster will flash every two seconds.
Disarming an Untriggered System
An armed system will be disarmed with one of these valid actions:

1. Pressing the UNLOCK button on the transmitter.

1. Placing a key in the door and turning to UNLOCK.

1. Turning the key to RUN or ACC.

The anti-theft alarm can be triggered by the following conditions:

• The ignition cylinder is damaged with or without the RAP being armed.
• A door is opened without disarming the armed RAP module.

The remote transmitter can activate a panic alarm which is similar to an anti-theft alarm, but does not deactivate the starter or cause the theft indicator to flash.
Disarming a Triggered System
If the system has been triggered, (the horn honks, the lights flash, and an external starter interrupt relay is engaged), the system can be disarmed by:

1. Pressing the UNLOCK or PANIC button on the transmitter.

1. Putting a key in the door and unlocking the door.

1. Turning the ignition to RUN/ACC (Turning the key to RUN/ACC will not disarm an alarm that has been triggered by the ignition lock anti-theft switch.).

there is a sensor that tells the anti theft module you used the key to unlock the door, it is attached to the door latch or lock cylinder, u must have disconnected the wire to the sensor, so it thinks u are breaking into the car.