Reset my engine oil low in 2007 chevy impala

When you disconnect the battery, you have to reset the security system and the engine immobilizer.

https://www.google.com/search?q=2007+Chevy+Malibu+LS+reset+security

How do I reset my 2007 chevy malibu anti theft?

Vehicle History https://www.vehiclehistory.com > questions > how-do-...
To reset the anti theft in a 2007 chevy malibu you will need to unlock the door with the fob, press the door lock button on the door, then close the door. Like.

4 answers · Top answer: In order to reset the anti theft system on Your 2007 Chevy Malibu You'll first need to put the key in the ignition and move it in to the on position. ...

How do i perform a chevy malibu security reset?

Vehicle History https://www.vehiclehistory.com > questions > how-do-...
First, park the car and make sure all doors are shut and locked. Then, slot in Your key into the driver side door and unlock the car. ..

Sometimes they just fail to reset properly. Nothing to worry about. The youtube video shows the procedure to reset for a Chevy Truck, should be the same for your Chevy car.

Here's a website with explanation.
https://www.quora.com/What-does-it-mean-if-the-change-oil-light-is-lit-after-an-oil-change

On a Chevy Impala or Monte Carlo with indirect TPMS, a totally different reset procedure is required. You can use the light switch or radio to reset the system. With the light switch procedure, turn the ignition on (engine off), the turn the light switch from OFF to parking lamps three times within five seconds. With the radio technique, turn the ignition on (engine off). With the radio off, hold the DISP button until “SETTINGS” is displayed. Use the SEEK button to scroll down the menu until you see “TIRE MON.” Press the PREV or NEXT buttons until “RESET” is displayed. Then press the DISP button again. You should hear a chime and see “DONE” to indicate the TPMS system has been successfully reset. Use the SEEK button to scroll through the menu until “DONE” is shown, then press DISP once more to exit from the learn mode.
Thank you for using fixya and good luck

There should be a reset button in the fuse pannel. It can be used to reset the low tire pressure light , and the change oil light.
Instructions should be in owners manual , or you can google it.
Chevy dealership should do it for free in my opinion.

Depress the accelerator pedal to the floor 3 times within 5 seconds.This is with the key on and engine not running.Hope this helps.Good luck.

YOU HAVE TO RESET OIL LIGHT.ITS DISPLAYED ON THE DRIVER SIDE INFORMATION CENTER.IT A CHECK MARK LOOKING SYMBOL..YOU PRESS HOLD RESET BUTTON FOR 5 SECONDS.

turn the key to the run position as soon as it is there hit the gass pedel three times with in 3 sec and it will reset.

turn ignition on with engine off press gas pedal to floor 3 times & light will flash then go out.
or if you have menu button on radio press button until reset oil life appears ten press enter

THIS SHOULD HELP YOU

Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.

Hi to reset the oil life monitor
turn the key on engine off
push the gas pedal to the floor 3 TIMES WITH IN 5 SECONDS
the light will flash then go out