No odometer ,no fuel gauge,no tachometer,no temp gauge all lights working

1. cluster failure whole or in part, check fuses first .(all cab/bay)
2. scan the PCm if the comm network fails it can not talk to the cluster then data to the cluster fails but does the ODOMeter roll and work for miles.?
3. the tachometer RPM uses PCM tachometer data, so the comms are dead.
4. see this drawing for (RPM) is best as engine runs but gauge not.

the clusted must get data from the PCM or fails
and the 2 fuses good.right one called METER,. 7.5AMP
TO FIX ANY MODERN CAR TAKES A SCAN TOOL

no info generic answer check fuses =wiring==connections

That's why you don't let you husband work on your car ! Unless he does it for a living .. For MPH there is a VSS - vehicle speed sensor , for the gas there is a sending unit in the fuel tank, for the temp. gauge there is a temp. sensor located in coolant stream on the engine .You more then likely need to have you instrument cluster repaired . GM had a problem with step motors inside the instrument cluster . A step motor is what controls the individual gauge. The sensors are all inputs to the PCM - powertrain control module (engine computer ) .
Engine Coolant Temperature Gage
The IPC displays the engine coolant temperature as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine coolant temperature. The engine coolant temperature gage defaults to C or below if:
?€¢
The PCM detects a malfunction in the engine coolant temperature sensor circuit.

?€¢
The IPC detects a loss of class 2 communications with the PCM.

Fuel Gage
The IPC displays the fuel level as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the fuel level percent. The fuel gage defaults to empty if:
?€¢
The PCM detects a malfunction in the fuel level sensor circuit.

?€¢
The IPC detects a loss of class 2 communications with the PCM.

When the fuel level is less than 14% (84ohms), the low fuel indicator illuminates.
Odometer
The IPC contains a season odometer and a trip odometer. Momentarily press the trip select/reset switch in order to toggle between the season odometer and the trip odometer. Press the trip select/reset switch for greater than 1.5 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The IPC displays the vehicle mileage and trip mileage as determined by the IPC. The IPC calculates the mileage based on the vehicle speed information from the PCM. The odometer will display 'error' if an internal IPC memory failure is detected.
PRNDL Display
The IPC displays the selected gear position as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the gear position. The PRNDL display shall flash all gear positions if:
?€¢
The PCM detects a malfunction in the transmission range switch circuit.

?€¢
The IPC detects a loss of class 2 communications with the PCM.

Speedometer
The IPC displays the vehicle speed based on the information from the PCM. The PCM converts the data from the vehicle speed sensor to a 4000 pulses per mile signal. The IPC uses the vehicle speed signal circuit from the PCM in order to calculate the vehicle speed. The speedometer defaults to 0 mph (0 kph) if a malfunction in the vehicle speed sensor circuit exists.
Tachometer
The IPC displays the engine speed as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine speed. The tachometer will default to 0 rpm if:
?€¢
The PCM detects a malfunction in the engine speed sensor circuit.

?€¢
The IPC detects a loss of class 2 communications with the PCM.

Need to replace two lights in the dash for the fuel gauge how to do this on a 2001 Pontiac Aztek 3.4 v6

Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Did you check the fuses?

if all guages just shut off, temp, blinkers, fuel guage, etc. check for a bad ignition switch.

Check the ground wire, could be corroded.

Take out the pc board and examine the copper traces. On my '94 Jetta I found one corroded trace that disabled the the same functions. I had to solder a wire to fix the connection. Good luck.

check for loose connection at the instrument cluster.