Hyundai getz radio

Best place would be from hyundai!

Remove the two 10 mm (head) bolts that hold the stop light. This bolts are between the tail light assembly and the tail gate weatherstrip. You can see them without having to remove anything.

By using a masking tape wrapped flat screwdriver, pry "back" the whole tail light assembly. Once out, you can twist the brake light (or reverse, or turn signal) bulb plug, remove and replace the bulb.

The Getz uses standard two filament brake globes (1/4 turn to install).

Best Manuals Fix your car right away by clicking the link I attached

Did you remove the battery or jump-start the car recently? that gives your radio an ICDE error.
To fix it: Easy fix - firstly, you'll need to remove the stereo to get to the serial number. Have the following tools ready, either: a) 2 metal rulers b) 1 metal ruler and 2 kitchen knives you don't mind bending c) 2 kitchen knives and one fork you don't mind bending d) possibly 2 forks will also work
Okay, here goes (I used option c):
1) use a kitchen knife to remove the black plastic border around your stereo. 2) on either side you should see the metal bracket and a smaller metal flap - place your fork between the bracket and the flap on the left hand side. jam it in quite far, so it can release the internal clips. 3) place your knives so that the flat (non-cutting) edges are touching and jam it in on the right side (basically so it works like a metal ruler for the clips, which I didn't have on hand) 4) use leverage to prise the whole unit out slightly. You can then remove it by hand. You don't need to remove it fully, you just need to see the serial number, which is on the top in the upper, right corner. 5) take the last 4 numbers of the serial and do some maths! You need to add 1/2/1/2 to the numbers in sequence. For example, if the last 4 numbers are 9462 then your maths should give you 0674 (9 1, 4 2, 6 1, 2 2). Another example is 1234=2446. Remember the number you end up with!! 6) start the electrics of your car (2 key turns). The radio should say ICDE. 7) For this example, pretend the number you ende dup with is 0674. Press the "1" on your stereo until the first number after ICDE says 0. Press "2" until the second number says 6. "3" until the third says 7 and "4" until the fourth says 4. You should end up with the display saying: "ICDE0674". Press the "5" on your stereo and MAGIC, your radio is working again!! 8) push the stereo back in at re-attach the face plate.
p.s. I accept no responsibility if you get zapped or break anything while trying this. I may feel a bit guilty (but not responsible, remember) if I hear on the news that you got zapped though. enjoy your tunes!

try another hyundai dealer in your area. Someone should have it on record somewhere. Tell them to stop being lazy..

hmm.....Try Removing The Ash Tray if I'm Not wrong There Should Be Two Screws That Hold The whole panel facing for the radio ect.

two pìn hoñes either side of the front of the radio ,push a special tool into these holes to remove the radio

I have an '03 Hyundai Accent 1600cc. I am told by the techies at the local dealer, the fuel filter is ON the fuel tank. You gain access to it by removing the back seat, then opening the panel beneath the back seat. Replace the filter, screw the panel back onto the floor and the job is done....

sometimes they put it in the owner manual or pack the manual comes in. if not dealer is the only way i know and unforuntally some charge.

The radio will have to be removed from the car dashboard

.Then please quote the MAKE + MODEL of your radio plus ALL the LETTERS and NUMBERS on any LABELS , BARCODES or STAMPED IN THE METAL CASING.


Also quote the MAKE of CAR it is fitted into.

Please note: Not all stereo codes can be calculated from the Serial Number