Need diagram for serpentine belt for 1998 ford escort zx2 that has 8 pulleys

The picture is for a zetec. Let me know if wrong diagram?

SECTION 303-05: Accessory Drive 1999 Escort/Tracer Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/06/1998 Accessory Drive Component Locations -2.0L SPI with A/C
Item Part Number Description 1 6B209 Belt tensioner 2 10344 Generator pulley 3 8620 Belt 4 3A733 Power steering pump pulley 5 8678 Belt idler pulley 6 2E884 A/C clutch pulley 7 6316 Crankshaft damper

Component Locations -2.0L SPI without A/C
Item Part Number Description 1 6B209 Belt tensioner 2 10344 Generator pulley 3 8620 Belt 4 3A733 Power steering pump pulley 5 6316 Crankshaft damper

Component Locations -2.0L Zetec
Item Part Number Description 1 10300 Generator pulley 2 19A216 Belt idler pulley 3 3D673 Power steering pump pulley 4 8509 Water pump pulley 5 6B209 Belt tensioner 6 19703 A/C clutch pulley 7 6B320 Crankshaft pulley damper 8 19A216 Belt idler pulley 9 8620 Drive belt NOTE: Drive belts (8620) with automatic drive belt tensioners (6B209) do not require adjustment.
NOTE: When a new drive belt is installed or a drive belt is re-installed after a service procedure, the drive belt does not fully seat into the pulley grooves until engine has run for several minutes.
This vehicle is equipped with:

• a V-ribbed serpentine accessory drive belt.
• an automatic drive belt tensioner.

New drive belts must be of the same type as originally installed.
Check the drive belt condition at 96,000 km (60,000 miles) then after every 24,140 km (15,000 miles).

email me at [email protected] and I can get a diagram to you so you know exactly what you are looking for under the hood.

Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 1998 Ford Escort ZX2, 2.0L DOHC In-Line 4-Cylinder Engine.
The Link says 2000 for the Year, however this is the same as the 1998 Year Model.

http://www.2carpros.com/car_repair_information/year/2000/make/ford/model/zx2/2000_ford_zx2_drive_belt_routing_diagram.htm

"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Here it is. 13mm wrench to rotate tensioner

If there is no diagram on the underside of your hood, or around the engine compartment, just wrap it around the crankshaft, and work your way around the pulleys, going flats to flats, ribs to ribs. There may be a couple of combinations, but you'll get it.

1) Start with the alternator.
2) Forward to the smooth idler
3) Forward to power steering
4) Down to A/C compressor
5) Back to crank pulley
6) Forward around tensioner
7) Back glancing off of water pump
8) Back glancing off of ribbed idler
9) Up around alternator (where you started)
Good luck!

This information can be found at www.serpentinebeltdiagram.com
They have all the belt routing info for any vehicle with a serpentine belt.
Hope this helps....

Go on the Dayco belts web site. They make serpentine belts and a pretty good data base of belt diagrams for any vehicle they make a belt for.

Call a Ford parts dept and ask them if you can get a routing diagram they can fax or pick it up thats the best way label take weeks to get in so do that and keep the copy in your car file Please rate my response thank you very much