How do you remove alternator from 1995 Maxima

1995-98 Models

1. Disconnect the negative battery terminal.
2. Remove the splash guard on the right side of the vehicle.
3. Loosen the alternator belt idler pulley.
4. Slip the drive belt off the alternator pulley.
5. Remove the four air conditioning compressor mounting bolts.
6. Remove the radiator fan and fan shroud.
7. Move the air conditioning compressor forward.
8. Disconnect the alternator harness connector.
9. Remove the alternator mounting bolts, and lower the alternator from the vehicle.

To install:

1. Hold the alternator in place and install the mounting bolts.
2. Plug in the alternator harness connector.
3. Move the air conditioning compressor back into location.
4. Install the radiator cooling fan and shroud.
5. Install the air conditioning compressor mounting bolts.
6. Place the drive belt on the alternator pulley.
7. Tighten the drive belt to the proper tension with the idler pulley.
8. Install the splash guard.
9. Connect the negative battery terminal.

Proper belt tension is important. A belt that is too tight may cause alternator bearing failure; one that is too loose will cause a gradual battery discharge and/or belt slippage, resulting in belt breakage from overheating.

How To Replace The Alternator On A Nissan Maxima ...

? 4:18
https://www.youtube.com/watch?v=RijNmGtnkqM
Dec 23, 2013 - Uploaded by jimthecarguy
Replacing The Alternator On A 2000 Nissan Maxima 3.0 Liter Not To Hard With These Short Cuts.

nissan maxima alternator replacement removal ... - YouTube

? 16:18
www.youtube.com/watch?v=QMp3hEmCJp8
Feb 25, 2015 - Uploaded by ****** knuckles Automotive
1996-2003 NISSAN MAXIMA / INFINITY ALTERNATOR REPLACEMENT REMOVAL INSTALLATION.

Disconnect battery, remove belt, disconnect wiring on alternator, loosen bolts and remove.

sounds like a dead Battery no longer chargable , have it tested if thats not the proble have your alternator tested, hope I helped.

Find alternator
Disconnect black cable
Disconnect red cable
Remove belt or pulley
Remove bolts
To reinstall complete same steps backwards

No, but you do have to take the fan and shroud off. then you pull the compressor loose and pull forward.

1. Disconnect the negative battery terminal.
2. Remove the splash guard on the right side of the vehicle.
3. Loosen the alternator belt idler pulley.
4. Slip the drive belt off the alternator pulley.
5. Remove the four air conditioning compressor mounting bolts.
6. Remove the radiator fan and fan shroud.
7. Move the air conditioning compressor forward.
8. Disconnect the alternator harness connector.
9. Remove the alternator mounting bolts, and lower the alternator from the vehicle.

Remove main belt first then remove the bottom and top bolts disconnect the plug on it and remove the other cord on it that runs from the battery.

go to wikipedia, from there i found detailed instructions and a video on a site http://www.ehow.com/video_2327320_removing-serpentine-belt.html

first you need to release the belt tensioner, and remove the belt. Disconnect the battery, and remove electrical plug on aternator. Then simply unbolt the old alternator, bolt in the new one, re-attach the the electrical plug, connect the battery back up, and re-install the belt. FYI this would be a good time to replace the serpentine belt.

TURN OFF RADIO TO KEEP FROM LOSING RADIO CODE.THEN YOU REMOVE NEGATIVE BATTERY CABLE.DISCONNECT THE 2 LEAD WIRES AND HARNESS CONECTOR FROM ALTERNATOR LOOSEN THE DRIVE BELT ADJUSTING BOLT AND REMOVE THE BELT. UNSCREW THE ALTERNATOR ATTACHING BOLTS AND REMOVE THE ALTERNATOR FROM VECHICLE.VISA VERSA PUT EVERY THING BACK.AND ADJUST ALTERNATOR BELT TENSION.WARNING DONT PUT TOO MUCH TENSION ON BELT.BECAUSE YOU WILL DAMAGE ALTERNATOR PULLEY BEARING.