Question about 1996 GMC Sierra

Open Question

96 gmc sierra 5 L engine wont start unless u hold the gas pedal to the floor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 91 Answers

SOURCE: 99 gmc wont start

try priming the engine, turn key to run possition, wait couple seconds for fuel pump to kick in, ( humming sound). turn key off... do that 7 times and should bring fuel to the thottle body, cuz you ran it dry there probaby no fuel in the lines

Posted on May 05, 2009

Ad
  • 148 Answers

SOURCE: 96 gmc sierra hard to crank after 12-14 hours

that has a votec engine in it the fuel pressure is droping at knight and it takes 60 psi before the injectors will fire most likely cause fuel pump ,leaking injector ,or a feul pressure regulator

Posted on Jul 14, 2009

litoshop
  • 298 Answers

SOURCE: brake pedal goes down to far abs brakes

Hi I'm litoshop if you bled the system and get no results then your brake pump needs to be replaced now before replacing make sure your pads are installed correctly because if there not this to can cause this problem good luck. if this information has been useful please let us know thank you.

Posted on Aug 11, 2009

  • 2 Answers

SOURCE: I have a 1988 GMC Sierra 1500 that wont stay running

1988 gmc runs for a little but dies. Check your c.t.s that checks the temp. of your coolent and when it fails it tells computor engin is hot, t.p.s takes over closes butterfly and chocks the air to keep engine from runnin to lean. If engine is not hot it will flood and stop runnin then some time will go by befor truck tries to start. May not be probablem but its a thought. c.t.s is located on manifold by top radiator hose neck. My truck was fine than sat had simmilor problem when i went to use again thats what i changed and seems to be back to normal. Hope this helps.

Posted on Sep 08, 2009

  • 5 Answers

SOURCE: 2004 gmc sierra clunk noise in drive line when

The drive shaft yoke is dry on the transmission out put shaft. When you stopp it slides in on the shaft, and then when you let go of the brakes the yoke sides back and goes clunk. Remove drive shaft and lubricate the splines in the yoke.

Posted on Jan 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 crown Victoria wont start had the problem couple weeks ago guy said the idle control was off now I guess doing it again I cleaned it but still wont turn over


When you say it wont turn over that implies that you can not hear the starter turning the engine over. If you can hear the starter cranking the engine over but the engine will not start try holding the gas pedal to the floor. Be prepared for the engine to start and let off the gas. If the engine stalls when you let off the gas try starting again but feather the gas pedal after it starts. It it stays running with the pedal depressed than I would agree that there is an issue with the IAC and it may need to be replaced.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Jul 31, 2013 | Cars & Trucks

1 Answer

1993 f350 460 cid wont start unless you press gas pedal to the floor


my truck starts right up if I hold the petal to the floor but wont start if I don't hold petal to floor

Feb 12, 2013 | 1993 Ford F350

1 Answer

How to turn off oil change message


Turn the key on but don't start the truck.
Push the gas pedal to the floor 5 times, then turn the key off.
Some models will do it with 3 instead of 5.

Jul 22, 2012 | 2004 GMC Sierra

1 Answer

How to reset change oil sign


I believe you turn the ignition to the on position (engine not running)and fully depress the gas pedal to the floor 5 times within 10 seconds. Sometimes you have to start the procedure over if it doesn't work the first time. Make sure you smoothly press the pedal all the way down and come all the way up each time. You should then hear a audible ding letting you know it reset.

May 02, 2011 | 2007 GMC Sierra 1500

1 Answer

Starts and runs good then suddenly ck eng lite come on and it dies. Will start back up with holding gas pedal on floor and die again soon...repeat...


Your vehicle is equipped wit the OBD!1 (on board diagnostic system ) when your check engine light turns on it is setting a code. You need to have it scanned to get this code. This will point you in a direction to your problem. When you place the accelerator to the floor you put the system in the clear flood mode which is allowing you to start but then the problem takes over and kills the engine.

Feb 20, 2011 | 1994 GMC Sierra

3 Answers

How to remove "oil change" code on 04 gmc sierra


Turn the key on,and press the gas pedal three times slow,within five seconds

Jun 08, 2010 | 2004 GMC Sierra

2 Answers

I have a 93 gmc c1500 4.3cy v6 with loss of power


The best thing to do is have auto zone check your codes for free and that would be a place to start from.

Feb 23, 2010 | 1995 GMC Sierra C1500

3 Answers

Change oil light on how do i reset after i changeded oil on 2003 gmc 6 cyl.


turn the key to the on position and press the gas pedal to the floor 6 times in rapid succession. than start the trurck without turning the key off

Apr 12, 2009 | 2003 GMC Sierra

2 Answers

2003 GMC Sierra 1500HD Panel Lights


as soon as you turn key on hit the gas pedal 3 times really fast you may need to do this a couple of times

Nov 13, 2008 | 2003 GMC Sierra 1500

4 Answers

Car shakes when trying to start and doesn't turn over


  1. hold gas pedal to floor while trying to start. do not pump pedal.
  2. holding pedal to floor is how you start a flooded f.i. engine

Nov 12, 2008 | 2000 Lincoln LS

Not finding what you are looking for?
1996 GMC Sierra Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...