1997 nissan kingcab ignition stuck in lock position can insert key and remove but won't turn ???

1-
My ignition key will not turn to off. I can remove the key, but it stays in the accessory mode. What's the fix?
My ignition key will not turn to off can remove the key but it stays in...

2.
Ignition key is stuck and does not turn Inspection Service & Cost
Ignition key is stuck and does not turn Inspection Service Cost...

3.
Ignition key won turn

You might have a bad ignition switch. Do the other accessory power features stay on too? Eg .... Radio, blower fan... Do the turn signals still operate when key is removed? But a bad multifunction switch (turn signal, headlight switch) coukd also be bad.

Put into park and press foot brake! Then release key!

Ignition - Key Stuck In Ignition Switch/Won't Turn Bulletin No.: 06-02-35-005 Date: February 28, 2006 TECHNICAL Subject: Key Stuck in Ignition, Key Will Not Return to Off Position, Shifter Button Won't Release in Park Position (Adjust Shifter Detent Finger) Models: 2002-2005 Chevrolet Monte Carlo Condition Customers may comment on any of the following conditions: - The key is stuck in the ignition cylinder. - They cannot return the key to the off position to remove the key. - The shifter button won't release in the park position. Cause This condition may be caused by the detent finger shifting over time. This may result in mis-alignment and binding of the shift rod on the shift position guide.
WHERE YOUR SHIFTER IS YOU WILL HAVE TO TAKE IT APART ..MAYBE THE RUBBER BOOT IS IT THE WAY,OR THE SHIFT LOCK SELINOID WHENT BAD

remove the steering coloum trim. Turn the key to run position, Press locking button on back of steering coloum housing assembly, Remove lock cylinder, Disconnect the ground strap from lock preload spring ( if equiped ) . Make sure key is still in run position when you reinstall.

If the key is non functional and you cannot turn to run then you will need the tool in this picture

METHOD 1 - NO TOOLS REQUIRED

1. Sit in the vehicle driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all of the vehicle's doors.
4. Press and HOLD the door "LOCK" switch to the "Unlock" position.
5. Insert and remove the ignition key twice (without rotating the ignition lock cylinder).
6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must be in the "OFF" position.
7. Release the door "LOCK" switch from the "Unlock" position (three fast chimes will be heard when the remote control door lock receiver enters the programming/diagnostic mode).
8. Press and HOLD the transmitter "LOCK" and "UNLOCK" buttons simultaneously for at least 12 seconds . Two fast chimes will be heard confirming successful programming.
9. Repeat step 8 for each additional transmitter to be programmed.
10. Remove the ignition key from the ignition lock cylinder

The final quarter turn of the key engages the steering lock. So while inserting your key, at position it gets stuck turn the steering left-right(to & fro) to loosen the locking pin such that now the key is free to turn the ignition. Oiling the steering locking pin would help too...........sodeep

take the plastic cover off the steering column, you will see a small hole at the bottom of the cylinder push in and pull out,thats all you have to do.

REMOVAL

1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
2. On all models, disconnect battery ground cable.
3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
4. Remove key light case from lock body, if equipped.
5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
6. On except 1989 Accord, place ignition lock in the I position.
7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.

INSTALLATION

1. On 1989 Accord models, install ignition lock cylinder as follows:

1. Place ignition lock cylinder in the LOCK position.
2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.

1. On except 1989 Accord, install ignition lock cylinder as follows:

1. Place ignition lock cylinder in the O position.
2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.

1. Install ignition switch and connect battery ground cable.

SRS wire harness is routed near the ignition switch.

CAUTION:

• All SRS electrical wiring harnesses are covered with yellow outer insulation.
• Before disconnecting the SRS wire harness, install the short connector on the airbag.
• Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.

IGNITION SWITCH

1. Remove the steering wheel, then remove the steering column covers.
2. Disconnect the 7-P connector from the under-dash fuse box.
3. Insert the key and turn it to "0."
4. Remove the 2 screws and replace the base of the switch.

I have 07 Pontiac Grand Prix, the wrong key was inserted into the ignition the other day. Now when I try to use the correct key it will not insert completly in the ignition, goes in until last 1/4in of key. Im stuck, I bought the new lock cylinder but how do I get the old one out? I cant get the key to insert all the way so I cant get it to the "On" position, it will not turn at all. The key that was inserted in error is whole and nothing is missing it seems like there is something stuck. Any help would be appreciated...