Change water pump on 2001 hyundai tiburon

Follow the detailed instruction within the workshop manual.

Go to YouTube, and enter "2005 Hyundai Tiburon GT valve timing" in the search box. You will find several videos that deal with changing the timing belt and water pump. Toward the end of each video, when they are reassembling the components, they will show the correct way to set the crankshaft pulley and cam pulleys to properly time the engine.

Your Cabrio has one of several 2.0L Volkswagen engines - determine your engine type from the
8th digit of your VIN, which will be either an "A", or "C",both are 2.0L engines.

Volkswagen 2.0L engines offered in 2001:
(a) 2.0L (Aba) Engine
(b) 2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine
(c) 2.0L (Aeg/Avh/Azg/Bdf) Engine

For completeness, I've included the water pump maintenance manual entries for all (3) 2.0L VW
engines offered in 2001. Note that the instructions below include (3) illustrations, which are
reproduced faithfully from the manual, but the last (2) illustrations are identical, since the last two
engines in the list above are virtually identical.

Volkswagen 2001 engines - water pump replacement

2.0L (Aba) Engine

Before servicing the vehicle, refer to the Precautions section.

Remove or disconnect:

1. Coolant

2. Thermostat housing from under the water pump housing.


Loosen but don't remove the bolts holding the pulley to the water pump.

Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing.


To install:


Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).





Fig. Water pump and thermostat housing-2.0L (ABA) engine

1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Coolant

Thermostat housing from under the water pump housing.



3. Loosen but don't remove the bolts holding the pulley to the water pump.

4. Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing. Refer to figure of ABA engine's water pump above.

To install:

1. Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

2. Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

3. Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine


1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Negative battery cable.

Coolant.

Accessory drive belt and tensioner.

Upper and center timing belt covers.



3. Position the engine so that the No. 1 cylinder is at TDC.
WARNING
Cover the timing belt to protect it from being contaminated with coolant.


4. Loosen the timing belt tension and slide the belt off the water pump sprocket.

5. Remove or disconnect:

Timing belt guard (2) mounting bolt (1), if equipped.

Water pump mounting bolts (5), then the water pump (4).

O-ring (3) and clean the seating area.


To install:







Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine

1. Install or connect:

O-ring, moistened with coolant.

Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

Timing belt guard, if equipped. Mounting bolt: 15 ft. lbs. (20 Nm).

Timing belt.

Upper and center timing belt covers.

Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

Accessory drive belt.

Coolant.

Negative battery cable.



2. Check and clear any DTCs, then match the ECM to the TCM.


2.0L (Aeg/Avh/Azg/Bdf) Engine


1. Before servicing the vehicle, refer to the Precautions section.

2. Remove or disconnect:
1. Negative battery cable.

2. Coolant.

3. Accessory drive belt and tensioner.

4. Upper and center timing belt covers.


3. Position the engine so that the No. 1 cylinder is at TDC.

WARNING
Cover the timing belt to protect it from being contaminated with coolant.

Loosen the timing belt tension and slide the belt off the water pump sprocket.

Remove or disconnect:

1. Timing belt guard (2) mounting bolt (1).

2. Water pump mounting bolts (5), then the water pump (4).

3. O-ring (3) and clean the seating area.


To install:






Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine


Install or connect:

1. O-ring, moistened with coolant.

2. Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

3. Timing belt guard. Mounting bolt: 15 ft. lbs. (20 Nm).

4. Timing belt.

5. Upper and center timing belt covers.

6. Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

7. Accessory drive belt.

8. Coolant.

9. Negative battery cable.


Check and clear any DTCs, then match the ECM to the TCM.

Here http://www.steeringpumps.com/hyundai-steering-pump/ you can find all details which are necessary for the power steering pump replacement. I found this to be useful and solves your problem

1.5L And 1.6L Engines



Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines




Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines



Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines




Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines




Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines



Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines



Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines




Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)



Fig. Installation of the timing belt-3.0L (VIN G) engine







Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

2001 Hyundai Tiburon 2.0L MFI DOHC 4cyl
The Fuel Filter is located Under hood, passenger side, front side of strut tower, mounted on fenderwell.



I hope help you with this, remember rated this help.

Good luck.

(1) No need to know if engine block coolant drain plug was available. Once the water pump was removed, all engine block coolant was drained. (2) After removing the three engine mounting bracket bolts, I also removed the mount bracket from the the body and made enough room to replace the timing belt easier.

yes in this case it is correct, the reason is that the water pump and the timing belt runs toghter.. you dont want to change one without the other..

1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

FUEL FILTER REPLACEMENT
1. Reduce the internal pressure of the fuel pipes and hoses by completing the following operations. (1)
Disconnect the fuel pump harness after removing the rear seat cushion. (2)
Start the engine and after it stalls, turn the ignition switch OFF. (3)
Disconnect the battery negative (-) terminal.
(4)
Connect the fuel pump harness connector

2. Remove the bolt connecting the fuel line with the fuel filter. Cover with a shop towel to avoid gasoline from splashing. 3. Remove the fuel filter mounting bolt, then remove the fuel filter from the fuel filter clamp. 4. After replacing the fuel filter, check for fuel leaks.