Cars & Trucks Logo

Related Topics:

Anonymous Posted on Apr 09, 2017

I have a 99 bdodge ram 2500 cummins im getting a 1689 code on my edge cts the truck starts but within seconds goes into an idol from 200 to 1000 rpm and back to 200 with a dead pedal ive got 18 psi on my lift pump which is a fass fuel system i have hot rod injection pump it starts fine then kicks into that idle also getting a fuel timing error code too ive got 12 volts on number 7 pin on injection pump pigtail with good ground on number 6 pin my fuel system relay is good ive bypassed the edge still does it this all happened as i was getting on it pulling onto freeway number 9 fuse in cab is good ....please someone help thank you

5 Related Answers

Anonymous

  • 4669 Answers
  • Posted on May 05, 2009

SOURCE: dodge cummins won't start, fuel reaching injector pump but no fuel coming out of injector pump.

You said you have fuel flowing from the inlet line of the injection pump? But not at the injector lines?

Ad

Anonymous

  • 1 Answer
  • Posted on May 10, 2009

SOURCE: 99 dodge 2500 5.9 cummins fuel pressure at 3psi

The 3 psi is caused by a failed transfer pump. The problem the loss of could be the VP44 injection pump. This pump should be run at min 7psi. I had the same fuel pressure problem. I replaced my stock transfer pump with a FASS DDRP from www.usdieselparts.com. The stock pump is over $200 to replace and will fail again, sometimes right out of the box. The DDRP will supply about 15psi to the pump and is simple to install. I hope this helps.

fingaz22

michael schultz

  • 1068 Answers
  • Posted on Oct 25, 2009

SOURCE: Where is Fuel Relay for 2004 Dodge Ram 3500 Diesel Truck

it doesn't have a fuel pump relay it has a fuel pump control unit and it is located on the chassis back quarter drivers side near the tube cross member for chassis on top of chassis rail near bed mount. locate the rear springs front perch and it will be above that on top of rail.

hope this helps. good luck and please ask any question you have.

Testimonial: "Thanx for info..no wonder I couldn't find Relay! "

Anonymous

  • 151 Answers
  • Posted on Apr 21, 2010

SOURCE: 2001.5 Dodge Ram Diesel 2500 4x4 Brake Pedal drops to floor

It sounds like you have a bad mastercylinder cause when you panic brake it doesn't have time to bleed through the valve in the cylinder but under normal braking your foot is on pedal longer in turn giving the fluid time to bypass the valve in the mastercylinder in turn the pedal going to the floor.

Testimonial: "thnx"

czaa

Arnie Burke

  • 7339 Answers
  • Posted on Dec 17, 2010

SOURCE: I changed both batteries on

sounds like a ground may not be rite--also chec the plug into the pump for corrosion--relay cud be bad-test it--ask a parts person where you bot the scanner to help you

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Just bought. 5.9 cummins Can`t get it to start without pushing gas pedal slightly. Runs good after warms up. Still have to give it fuel to start.

Numerous Conditions May Cause Engine to Crank But Not ...

repairpal.com > Problems > Dodge > Ram 2500
2006 Dodge Ram Laramie 2500, 5.9i liter Cummins ... I know in the old days the dodges had a way about starting up an engine and that would be where.

White smoke, rough idle at startup - Dodge Cummins Diesel Forum

www.cumminsforum.com > ... > 3rd Gen. Powertrain
Jun 5, 2010 - 9 posts - ‎7 authors I have an 06 Dodge 5.9L that has a light white smoke and rough idle when first ... 2006Ram 2500 QCSB 4x4, 3" Carli coils w/ 1" Daystar spacer, ... Still ran good tho, dispite the exact conditions you describe on Cold Start up.
0helpful
1answer

I have a 2001 Dodge Cummins 2500. When I Turn on the lights, the engine dies. It's showing codes 1693,1694, and 1689.

Hi.

First of all most of the codes you posted are companion codes (OEM if I remember), I would check with some OBDII scanner for the generic codes (For instance : P0447) first then I can give you a hand. That way I can direct my diagnosis on the correct circuit or component.
0helpful
1answer
0helpful
1answer

Error code 1689

P1689 DODGE - Battery has been Disconnected in the last 50 engine starts
1helpful
1answer

How do reset a 2005 dodge 2500 cummins

If you are talking about resetting the codes of the computer, most cars can be done by just disconnecting the battery for about 5 minutes.
0helpful
1answer

I have a 99 dodge ram 2500 cummins, the rear end recently started chattering when turning, especially noticeable off the start, i did clean out my rear diff and added diff fluid to the bottom of the hole,...

MORE THAN LIKELY YOU NEED TO ADD THE FRICTION MODIFIER TO THE REAR AXLE FLUID..THIS TRUCK CALLS FOR 80W90 GEAR OIL AS WELL..I HOPE THIS HELPS..HOPEFULLY NO DAMAGE HAS BEEN DONE TO CLUTCH PACKS IN CARRIER
0helpful
1answer

Dodge Ram 2500 Cummins Diesel 2001. Starter hangs up when start

Have you had a mot or try checking with an mechanic¬!
20helpful
2answers

1999 DODGE CUMMINS SHUT DOWN FAULT CODES p1689, p1688

P-1689 NO COMMUNICATION BETWEEN ECM & INJECTION
PUMP MODULE
0helpful
1answer

2005 ram 2500 cummins won't upshift from first until 2500 rpm

check the fluid and how hard does it shift when it does shift?
0helpful
1answer

RPM Oscillating

have you had the vehicle speed control reprogrammed if not that could be your problem
Not finding what you are looking for?

90 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...