Locked keys in my 2010 Lincoln MKS. The code on the keyless door entry will not work.

Hi,try this. How to program your keyless entry keypad

have you changed the battery in your remote?

We have no way to provide that code.

How can a lock not lock or unlock with a physical key? Maybe the cylinders are frozen? Try squirting a little oil into the locks.
1996 Town Cars have keys and keyless entry. The physical keys are two, an ignition key and a door key. You can't use the door key in the ignition, nor the ignition key in the door. They aren't interchangeable.
The default key code for keyless entry is posted on the right trunk hinge, inside the trunk.

KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time.

1. Enter the five digit permanent entry code into keyless entry keypad.
2. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code. (Factory code found on the module).
3. Enter any alternate five digit code within five seconds of pressing 1/2 button.
   • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code: 9/0-- no memory recall
     1/2-- memory seat position 1
     314-- memory seat position 2
     5/6-- memory seat position 3
     
   • After successful programming, the doors will signal by locking and then unlocking.
   
   

The Keyless Entry Module is located inside the drivers side door.

Using your keyless entry on the keypad, press the 5 digit code to get into the door and press the 6 key immediately after. Lincoln has several codes in addition to the 5 digit keyless entry like pressing the 3 to open all the doors, the 6 for the trunk and pressing the last 2 buttons at the same time to lock the doors.

Enter the keyless entry code on the door keypad 3 times. Locks will cycle down and up after the third time. Press and release the "lock" button. Locks should cycle again. May need to hold down lock button for 2 sec rather than press and release. Program up to 4 remotes. If cycling the key on-then-off works, you'll probably have to do it quickly 8 times and after the 8th time, locks will cycle down then up and press and release the lock button.

Hello
this is how to program the remotes/keyless entry

How

• Obtain all remote transmitters
• enter the 5 digit permanent code into the keyless entry pad on the drivers door
• Press the 1-2 switch on the keyless entry pad
• Within 5 seconds
• Press any button on the first remote transmitter
• The doors should open then lock
• Within 5 seconds
• press any button on the second & third remote
• within 5 seconds for each remote
• to exit programming
• simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds

NOTE
The 5 digit permanent code is located in one of the following places

1. On the owners warranty card
2. On the label on the inside the trunk/ boot
3. On the owners code card
4. On the centrel locking control module located in the drivers door
5. In the PCM ford can get this for about $25.00

I hope this help
Regards Paul
www.limotec.co.uk

I locked the 2000 lincoln continental with the key fob but lost it now the ignition key wilolo not unlock the door