2002 BMW 3 Series Logo

Related Topics:

A
Anonymous Posted on Jul 28, 2017

Remote keycontrol the remote key does not work.the second one is working.the one with the problem is working correctly with the ignition.it s just does not give signal to open the doors.i changed the battery but nothing happened.the only thing i checked in a digital counter is that when i push the buttons it s sometimes gives signals but not all the time.i also cleaned the pad with a special contact cleaner but still nothing

5 Related Answers

onyeredson

Paul W

  • 404 Answers
  • Posted on Jan 19, 2009

SOURCE: Central Locking not working

Hi Craig,
I'm running a E34 Tds Touring with a similar problem, my rear doors and tailgate have dropped of the central locking circuit.
I have been told it is the Central locking Module a large black box under the dash that is faulty, apparently a common problem.
Hope this points you in the right direction,
Please remember to rate my effort!
Paul 'W'
Onyer~EDson(:0) {#><U.K.

Ad

Anonymous

  • 11 Answers
  • Posted on Aug 03, 2009

SOURCE: 2000 Toyota Corolla wont start Changed 02 sensor disconnected bat

Check your alarm. because the alarm system has a engine immobilizer which makes the engine do what you are experiencing. Take the car to the dealer and tell them what is going on and they will reset the car system.

Anonymous

  • 19 Answers
  • Posted on Sep 22, 2009

SOURCE: Central Locking does not work

You must reset your remote control in order for the lock/unlock to work properly.

To reset remote you would:
1)Insert Key in Ignition Turn to Position 1(Don't Start the Engine) for about 5 seconds
2)Turn Key Off and HOLD the LOCK button on Remote while pressing the UNLOCK 3 TIMES
3)Release both lock and unlock buttons you are holding
4)All doors should automatically unlock

And exit the door and lock with the Remote.

Anonymous

  • 510 Answers
  • Posted on Dec 22, 2009

SOURCE: my key does not open or lock my doors remotely had

You do not say what year your car is, here is standard programming for most bmw,s,after battery or key replacement or malfunction.
Unlock car,enter, make sure all doors boot etc are closed.
Switch ignition on and off,remove key.
PRESS AND HOLD unlock button.
Press lock button 3 times in 10 seconds
Release unlock button
Some models led flashes in key for 10 seconds
Later keys central locking will lock unlock rapidly to confirm reset.
Later keys without led has no battery replacement,as it charges as you drive.So if you have this type charge before reprogramming

gazkatbear

  • 55 Answers
  • Posted on Feb 27, 2010

SOURCE: remote central locking on BMW 535d wont work.

replace the battery in key head.if unsurehow to take to bmw dealer

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

06 durango no radio heated seats locks on fob and other things improperly working

Procedure #1 (Remote Head Keys WITH Immobilizer Chip)
Step-by-Step How To Programming Instructions:
  1. CUT the NEW remote head key for your vehicle.
  2. INSERT the first working remote head key into the Ignition.
  3. TURN the Ignition to the ON position for at least three (3) seconds but no longer than fifteen (15) seconds.
  4. TURN the Ignition to the OFF position and remove the first remote head key.
  5. INSERT the second working remote head key into the Ignition.
  6. TURN the Ignition to the ON position for at least three (3) seconds but no longer than fifteen (15) seconds.
  7. After ten (10) seconds a chime will sound and the vehicle's security light will begin to flash.
  8. TURN the Ignition to the LOCK position and REMOVE the second remote head key.
  9. INSERT the NEW remote head key into the Ignition.
  10. TURN the Ignition to the ON position within 60 seconds.
  11. After ten (10) seconds a single chime will sound and the vehicle's security light will stop flashing.
  12. The vehicle's security light will turn ON again for three (3) seconds and OFF to indicate successful programming.
  13. Test all remotes. Programming is now complete. The remote and key are now both programmed.
  14. If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Procedure #2 (Remote Head Keys WITHOUT Immobilizer Chip)
Step-by-Step How To Programming Instructions:
  1. ENTER the Vehicle and CLOSE all doors.
  2. INSERT key into Ignition.
  3. TURN the Ignition to the ON position (before cranking).
  4. PRESS and HOLD UNLOCK on a working remote head key for four (4) to ten (10) seconds.
  5. WHILE holding the UNLOCK button, PRESS the PANIC button UNTIL a chime sounds to indicate entry into Programming Mode.
  6. RELEASE both the PANIC and UNLOCK buttons.
  7. PRESS the LOCK and UNLOCK buttons simultaneously on the same remote until a chime is heard.
  8. Once the chime is heard, PRESS and RELEASE the UNLOCK button on that same remote. Another chime will sound indicating successful programming of that remote. (This MUST be done within 30 seconds)
  9. WITHIN 30 seconds of Step 8, PRESS the LOCK and UNLOCK buttons on any other remotes to be programmed. RELEASE the buttons when the chime is heard. Again, PRESS and RELEASE the UNLOCK button on that remote. Another chime will sound indicating successful programming of that remote.
  10. REPEAT Step 9 for ALL remotes (even working remote head keys) that you want to work with your Vehicle.
  11. Test all remotes. Programming is now complete. The remote and key are now both programmed.
  12. If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Hope one of these helps.
0helpful
1answer

2013 Toyota Highlander. Key fob remote doesn't work after installing new battery. It is not a smart key remote.

PROCEDURE. Make SURE the battery you installed is good.
  • Driver's door open, key removed from ignition switch
  • Within 5 seconds: Insert and remove the key from the ignition switch twice
  • Within 40 seconds: Close and open driver's door twice
  • Insert and remove the key from the ignition switch. Close and open driver's door twice
  • Insert the key into the ignition switch and close the driver's door
  • Within 40 seconds: Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program and remote transmitter code whilst erasing the original codes. Three times to check how many remote transmitter are currently registered or five times to erase all registered codes
  • Remove key from ignition switch. System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered
  • Within 40 seconds: Press and hold LOCK and UNLOCK buttons simultaneously for 1.5 seconds
  • Within 3 seconds: Press LOCK button
  • SYstem should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed
  • Within 40 seconds: Repeat button procedure to program remaining remote transmitters.
  • NOTE: To exit programming mode: Open driver's dorr
  • NOTE: A maximum of 4 remote transmitters can be programmed
If the above programming procedures do not work, then you should contact your locksmith.

Goood Luck!
0helpful
2answers

How to get into programming mode to program a remote?

Few Toyota models came equipped with remote door locks before 2008 - surprisingly!

Your car may not have the radio receiver to work with door locks. In that case, you need the radio and some wireing to pair with your remotes.
0helpful
1answer

I have a 00 petrol ford focus but the fob key does not work anymore. I saw a programming explanation for a 02 diesel focus and I am wondering if there is such a solution for my car? Thank you.

OBTAIN ALL REMOTE TRANSMITTER. TRY THIS PROCEDURE.FASTEN SEAT BELTS AND CLOSE ALL DOORS.TURN IGNITION SWITCH FROM OFF TO ON 4 TIMES WITHIN 6 SECONDS.SWITCH IGNITION OFF,ACOUSTIC SIGNAL WILL SOUND AND SYSTEM WARNING LAMP WILL ILLUMINATE INDICATES CORRECT PROGRAMMING.WITH IN 10 SECONDS.PRESS AND HOLD ANY REMOTE TRANSMITTER BUTTON. WAIT FOR ACOUSTIC SIGNAL AND SYSTEM WARNING LAMP TO FLASH INDICATES CORRECT PROGRAMMING. TO PROGRAM ANOTHER REMOTE TRANSMITTER, REPEAT ABOVE PROCEDURE WITHIN 10 SECONDS.TO EXIT PROGRAMMING MODE,TURN IGNITION SWITCH TO CRANK OR WAIT 10 SECONDS. IF THIS PROCEDURE FAILS YOUR IGNITION KEY WORN OR IGNITION SWITCH RING COIL BAD.
1helpful
3answers

MY PT Cruiser Functional transmitter and the one to be programmed both have no "PANIC" Button . How I programme the spare Fob

If you don't have the Panic button then sorry, you can't program yourself, the dealer will have to program it to the RKE (Remote Keyless Entry) module in the vehicle, using their DRB scan tool.
0helpful
1answer

Acura RL 2000 Remote needs Program Instructions

TURN ON IGNITION SWITCH WITH ENGINE OFF.POINT THE REMOTE TRANSMITTER AT CENTRAL LOCKING SIGNAL CONTROL MODULE LOCATED BEHIND PASSENGERS SIDE C POST.WITHIN 4 SECONDS PRESS LOCK OR UNLOCK.WITH REMOTE TRANSMITTER.WITHIN 4 SECONDS SWITCH IGNITION OFF.WITHIN 4 SECONDS SWITCH ON IGNITION WITH ENGINE OFF.WITHIN 4 SECONDS PRESS LOCK OR UNLOCK USING REMOTE TRANSMITTER.WITHIN 4 SECONDS SWITCH OFF IGNITION SWITCH.REMOVES KEYS FROM IGNITION SWITCH WAIT 10 SECONDS THEN TRY USING REMOTE TO SEE IF IT WORKS DOOR LOCKS.IF THIS PROCEDURE DONT WORK.TAKE TO DEALERSHIP.
23helpful
2answers

2002 bmw 530i key does not (remotely) unlock doors or trunk but they work fine manually.

Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.
1helpful
1answer

Keyless control not work

here ya go follow the steps exactly and it will work and dont forget to rate me please,

* Remote programming

Start with drivers door open, unlocked, and no key in the ignition.
Insert and remove the key from the ignition switch twice within 5 seconds.
close and open the driver door twice within 40 seconds.
Then insert the key into the ignition key cylinder and remove it.
Close and open the driver door twice within 40 seconds.
Then insert the key into the ignition key cylinder and close the door.
Turn the ignition switch from LOCK to ON and back once and remove key
Locks should cycle once.
Within 40 seconds press the LOCK and UNLOCK switches on the transmitter switch simultaneously for 1.0 – 1.5 seconds.
Within 3 seconds after the previous operation, press either one of the switches for more than 1.0 seconds.
Within 3 seconds after the transmitter switch has been turned OFF, the LOCK–UNLOCK operation will be automatically performed once if the registration of the recognition code of the transmitter is completed correctly.
In case the LOCK–UNLOCK operation is performed twice, the registration of recognition code has failed.
Perform the registration procedure from the beginning once
5helpful
1answer

Remote key fob will not work-battery replaced

VW/AUDI/SEAT/SKODA



Remote Control Programming (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Using the remote control press the Unlock button once, and the horn
will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.

For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote
control.

Remote Control Erasing (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Press the remote control unlock button 5 times in 1 second intervals.
A short horn will sound.

4. Wait 6 seconds and press the unlock button once to activate memory
erase.

5. Switch ignition OFF, all remotes are now erased.
0helpful
2answers

How to program the key for my bmw 750i model 1997 to lock/unlock the door

BMW 7-Series - Key Remote Programming
Three methods to try:
Method 1:
1. Working from within the vehicle and with the doors shut
2. Turn ignition to position 1 and back to off within 5 seconds.
3. Remove the key from ignition and press and hold the unlock button for 15 seconds during this time press the key lock button 3 times within 5 seconds.
4. Release both buttons.
5. Doors will lock and unlock to show correct programming has occurred.

Method 2:
To do this procedure you need to have one working key and one key that needs to be programmed.
1) Get in and close all doors.
2) Turn on the ignition and turn off quickly. (No more than 5 seconds) to start the process. Next action must take place within 30 seconds.
3) Remove the 1st key.
4) Hold the key up near your left shoulder (this is so it is closer to the remote receiver antenna.
5) Hold down the unlock button and press the lock button 3 times. Release the unlock button and the doors lock which confirms the operation.
6) Quickly repeat steps 4 & 5 for key #2 etc.
If it does not work, try doing the keys in opposite order. Key 2 then key 1, vs 1 then 2.

Method 3:
Alternate if you do not have a working remote
1. Turn key to position 1 five times very quickly 2. Remove key 3. Hold unlock button then press lock button 3 times, release unlock button.
4. If you have another key do the same button pressing within 30 seconds 5. Turn on ignition to finalise.
PLEASE NOTE: This programming procedure programs the remote control part of the key. Any transponder chip for the immobiliser (starting of car) will not be programmed and must be done by a specialist.
window.google_render_ad();
Not finding what you are looking for?

54 views

Ask a Question

Usually answered in minutes!

Top BMW Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

old marine
old marine

Level 3 Expert

2426 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...