Front end noise

the squeaking sounds like a wheel bearing going bad. And the pulling to one side is cause by unequal braking pressure caused by plugged rubber brake hose, bad calipers or wheel cylinders. Check the bearings by lifting the car with a jack, block the wheels, and use a jack stand for safety. now wiggle the tire around. If it has any play, the bearing is bad. Replace it. I would replace your brakes as well. Good luck

Ensure the wheel nuts and Axle nuts are properly torqued to the specification. Lift up the front wheels, place supports under the car and do the following:
- Sit if front of right wheel, slightly move it right and left and feel any abnormal noise if coming out of it. If click-click or Tuck-Tuck sound is observed it could be due to the excessive play in the tie rod end, rack end, ball joint wheel bearing or U joint. Next hold the Tire with your one hand at the top and with other hand at the bottom. Shake the Tire inside out and feel any noise or play. If play is observed, it could be the worn out ball joint or the wheel bearing. Now hit the Tire at the top with rubber hammer and observe any rattling noise coming from near the center of the wheel. If you could listen to the extra noise it could be due to the dried up caliper pins. Grease the pins with graphite grease. If all is found fine, similarly check the left wheel and repair as necessary.

To troubleshoot the issue,go through the help link mentioned below:---
CARS: Working of
tire pressure monitoring systemhttp://technoanswers.blogspot.in/2012/10/cars-working-of-tire-pressure.html-------------
GMC ENVOY spare tire system stopped working?http://repairhelpcenter.blogspot.com/2012/01/gmc-envoy-spare-tire-system-stopped.html

TIRE PRESSURE LIGHT COMING ON?
http://whoisbyme.blogspot.in/2012/07/tire-pressure-light-coming-on.html

What is Best Tire For the Vehicle?http://technoanswers.blogspot.in/2012/04/what-is-best-tire-for-vehicle.html------------
1998 Toyota
Camry: Tires Make Knock Rattling Noise Over Bumps?http://whatisbyme.blogspot.in/2012/05/1998-toyota-camry-tires-make-knock.html

These will help. Thanks.

TIRE PRESSURE MONITOR SYSTEM
The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. If your vehicle has this feature, sensors are mounted on each tire and wheel assembly, except the spare tire. The TPMS sensors monitor the air pressure in your vehicle's tires and transmit tire pressure readings to a receiver located in the vehicle.

The TPMS is designed to alert the driver, if a low tire pressure condition exists. This system also allows the driver to check tire pressure levels using the Driver Information Center (DIC).

When a low tire pressure condition is detected, the TPMS displays the "CHECK TIRE PRESSURE" warning message on the DIC, and at the same time illuminates the low tire pressure warning symbol.

You may notice, during cooler weather conditions, that the tire pressure monitor light, located on the instrument panel cluster, and the "CHECK TIRE PRESSURE" message will appear when the vehicle is first started and then turn off as you start to drive the vehicle. This could be an early indicator that the tire pressures are getting low and need to be inflated to the proper pressure.

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper inflation pressure for those tires.)

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated.

Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

The "CHECK TIRE PRESSURE" warning message and low tire pressure light (telltale) will appear at each ignition cycle until the tires are inflated to the correct inflation pressure.

The Tire and Loading Information label (tire information placard) shows the size of your vehicle's original tires and the correct inflation pressure for your vehicle's tires when they are cold.

Your vehicle's TPMS can alert you about a low tire pressure condition but it does not replace normal tire maintenance.

NOTICE: Do not use a tire sealant if your vehicle has Tire Pressure Monitors. The liquid sealant can damage the tire pressure monitor sensors.

RESETTING THE TPMS IDENTIFICATION CODES
Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. Each tire/wheel position is matched to a sensor, by increasing or decreasing the tire's air pressure. The sensors are matched to the tire/wheel positions in the following order: LF TIRE (left front tire on the driver's side of the vehicle), RF TIRE (right front tire on the passengers side of the vehicle), RR TIRE (right rear tire on the passengers side of the vehicle), and LR TIRE (left rear tire on the driver's side of the vehicle).

You will have one minute to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than one minute, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you will need to start over.

The TPMS sensor matching process is outlined below:

1. Set the parking brake.
2. Turn the ignition switch to "RUN" with the engine off.
3. Turn the headlamp switch from "OFF" to the parking lamps setting four times within three seconds. A double horn chirp will sound and the TPMS low tire warning light will begin to flash. The double horn chirp and flashing TPMS warning light indicate that the TPMS matching process has started. The TPMS warning light should continue flashing throughout the matching procedure. The "SERVICE TIRE MONITOR" message will be displayed on the Driver Information Center (DIC).
4. Start with the driver's side front tire.
5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for 10 seconds, then stop and listen for a single horn chirp. The single horn chirp should sound within 15 seconds, confirming that the sensor identification code has been matched to this tire and wheel position. If you do not hear the confirming single horn chirp, you will need to start over with Step 1. To let air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gage or a key.
6. Proceed to the passenger's side front tire, and repeat the procedure in Step 5.
7. Proceed to the passenger's side rear tire, and repeat the procedure in Step 5.
8. Proceed to the driver's side rear tire, and repeat the procedure in Step 5.
9. After hearing the confirming horn chirp for the left rear tire, check to see if the TPMS warning light is still flashing. If it is, turn the ignition switch to LOCK to exit the sensor matching process. If the TPMS warning light is not flashing, the five minute time limit has passed and you will need to start the process over beginning with Step 1.
10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.
11. Put the valve caps back on the valve stems. The spare tire does not have a TPMS sensor. If you replace one of the road tires with the spare, the "CHECK TIRE PRESSURE" message will be displayed on the DIC screen. This message should go off once you re-install the road tire containing the TPMS sensor. The "SERVICE TIRE MONITOR" message is displayed when the TPMS is malfunctioning. One or more missing or inoperable TPMS sensors will cause the service tire monitor message to be displayed.

This sounds like a bad strut, one or both on the front has gone bad. Here is a picture of just the strut with out the spring. The price ranges from $65.00 to $220.00 depends on what you can afford.

Hello and welcome. this requires a high end scan tool to check. but since the left front tire does read any pressure. this is usually a bad tire pressure sensor. this is probably why the service tire pressure light is on. the sensor is mounted on the tire stem inside the wheel. this requires the tire to be removed from the wheel to replace sensor

The first thing to check on a rattling noise is if going over minor bumps in the road if that is when it makes noise is a sway bar link, they make a rattling noise. If you raise that wheel up you might also want to try and wobble the wheel to be sure it is not a tie rod end or ball joint. Typically I run into the sway bar links or the sway bar bushings making the noise. However ive even seen it be a rock sitting on the strut plate.

The sway bar linkage probably came undone on one of the sides. Wikipedia has a picture of what your sway bar linkage may look like:

http://en.wikipedia.org/wiki/Sway_bar

That is a picture of a Porsche sway bar, but the idea is the same. Make sure all bolts are tight and that one end is not missing the linkage that connects it to the spring/strut. The grinding of the brakes may be the sound of the linkage piece touching the rotor. Sway bar is a logical solution to both issues.

If that doesn't fix the issue, put the front end of the truck on blocks or jack stands and have somebody wiggle the tire up/down and side to side while you inspect the mechanical components underneath. Other things to check may be the ball joints, tie rod ends and suspension bits.

Jack car up, turn wheel by hand if grinding sound replace wheel bearing.

could be tie rod ends. but you should have a toyota tech check them.

hope this helped.
please rate good.

If you need further help, reach me via phone at https://www.6ya.com/expert/mark_445a24324be9eb03