Question about 2004 Chevrolet Silverado

1 Answer

Need the correct torque specs for 2004 silverado 1500 calipers

Need the spec for bothe calipers and mounting bracket

Posted by on

  • 2 more comments 
  • Anonymous Mar 28, 2009

    You are the man!

  • Anonymous Mar 15, 2014

    Need correct specs for caliper on 2006 Avalon

  • Anonymous Mar 18, 2014

    Replaced caliper and need proper specs

  • Anonymous Mar 27, 2014

    torque specs

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 33 Answers

  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Posted on Mar 28, 2009

    • Anonymous Mar 28, 2009

      thanks dont forget to rate it

    ×

    Ad

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE:

    Hi there,
    Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

    Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

    Here's a link to this great service

    Good luck!

    Posted on Jan 02, 2017

    Ad

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    2004 Kia Optima Brake Torque Spec


    Bracket bolts Front 16-24 ft/lbs
    Caliper bolts Front 51-63 ft/lbs Rear 16-24 ft/lbs

    Feb 03, 2017 | 2004 Kia Optima

    1 Answer

    What are the 2010 journey brake caliper torque specs


    SPECS???? ON A CALIPER...NO,NO,NO! CALL DEALER

    Jul 03, 2014 | 2006 Chevrolet Suburban

    1 Answer

    Chrysler caliper bracket


    you will need the rotors, calipers, brackets, and pads off of a 300c

    Apr 28, 2013 | Cars & Trucks

    1 Answer

    Need torque specs for brake caliper bracket bolts.2000 grand prix


    Hello and welcome. here is the torque specs for the bolts.

    Caliper Bolts
    85 N·m
    63 lb ft
    Caliper Bracket Bolts
    180 N·m
    133 lb ft
    Caliper Bolts
    85 N·m
    63 lb ft
    Caliper Bracket Bolts
    180 N·m
    133 lb ft
    caliper brake bracket bolts torque to 180 n.m or 133 ft.lbs

    Jul 26, 2010 | 2000 Pontiac Grand Prix

    1 Answer

    I need the torque specs for the 4 hus assy bolts and the 2 caliper bracket bolts on a 2004 dodge 2500 4wd...do you have them?


    Caliper Bolts Torque ...... 24 ft. lbs
    Hub/Bearing Bolt ........... 122 ft. lbs
    Hub/Bearing Nut ............ 180 ft. lbs

    Feb 06, 2010 | 2004 Dodge Ram 2500

    1 Answer

    2004 silverado rear brake torque specification, had to replace rotor, need specs for both the set that attaches caliper bracket to knuckle and calipers to bracket, the pads that are required is GMKD792


    31 ft lbs for caliper to bracket, then caliper bracket to nuckle is.148 ft lbs for 6400 & 7200 lbs GVWR or
    122 ft lbs for 9900 lbs GVWR or
    221 ft lbs for 12300 lbs GVWR.
    good luck hope this helps.

    Dec 21, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

    1 Answer

    Rear wheel bearing removal


    First disconnect the neg battery terminal. Raise the vehicle and support it with jack stands. Remove rear tire. Remove the 2 caliper bracket mounting bolts don't remove the caliper from the bracket though and using some wire hang the caliper and bracket up out of the way (hang it off the spring) the rotor should come right off. At this point you can disconnect the abs wire that's plugged into the back of the hub and loosen the 4 wheel bearing hub attaching bolts. You may have to tap on the old hub with a hammer to break it free from the mounting surface a couple of good whacks should do it. Make sure the mounting surface is clean. Reassemble in reverse. Have the auto-parts store that you buy the new hub from give you the proper torque specs for tightening the bolts I believe its around 25 ft lbs. but have them look it up to make sure.

    Nov 21, 2009 | 2000 Pontiac Grand Prix

    1 Answer

    Is there a torque spec on the spindle nut for the rear caliper on a 1999 Chevy Silverado 4x4 V8 5.3


    1. nstall the caliper mounting bolts. Perform the following procedure before installing the caliper guide pin bolts (15 Series only).
    2. Remove all traces of the original adhesive patch.
    • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
    • Apply Red Loctite#272 to the threads of the bolt.
    1. Install the caliper mounting bolts (25 series). Tighten the caliper guide pin bolts to 42 Nm (31 ft. lbs.) on the 15 series; 108 Nm (80 ft. lbs.) on the 25 series.

    Nov 19, 2009 | 1999 Chevrolet Silverado 1500

    2 Answers

    Brake job torque spec


    Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

    Nov 13, 2009 | 2005 Honda Civic

    1 Answer

    Silverado 1500 Z71 off road, 5.3L. Details on fr


    This is for the front: Removal & Installation
    1. Remove 2/3 of the brake fluid from the master cylinder.
    2. Remove or disconnect the following:
      • Wheel
      • Caliper. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
      • Caliper mounting bracket bolts
      • Caliper mounting bracket from the steering knuckle assembly
      • Brake pads from the caliper mounting bracket
      • Clips from the inside ends of the caliper mounting bracket and discard
    To install:
    1. Install or connect the following:
      • Clips to the inside ends of the caliper mounting bracket
      • Brake pads to the caliper mounting bracket
      • Inner pad (1 wear indicator)
      • Outer pad (2 wear indicators)
      • Caliper mounting bracket to the steering knuckle assembly
    2. Perform the following procedure before installing the caliper mounting bracket bolts:
      • Remove all traces of the original adhesive patch.
      • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
      • Apply red Loctite®272 to the threads of the bolt.
    3. Install or connect the following:
      • Caliper mounting bracket bolts to the steering knuckle. Tighten the caliper guide pin bolts to 74 ft. lbs. (100 Nm) on 15 series or 80 ft. lbs. (108 Nm) on 25/35 series.
      • Caliper
      • Tire and wheel assembly
    4. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly in order to seat the brake pads. Burnish the brakes as needed.

    Oct 12, 2009 | 2003 Chevrolet Silverado 1500

    Not finding what you are looking for?
    2004 Chevrolet Silverado Logo

    7,756 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    Marvin
    Marvin

    Level 3 Expert

    85206 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...