Kill switch automatically activates

Shut driver door and unlock with key this should turn off alarm

The 'Keyless Entry & Burglar Alarm System" is activated. You must 'Disarm' the system using the Keyless Entry Remove (Key Fob) to "Reset" the system. The reason the engine won't start is due to the burglar alarm - it has a "Starter Kill" circuit which is activated when the alarm is activated. The alarm must be DEactivated to DEactivate the 'Starter Kill' circuit.
Another way to start the engine is to get in the car, put the key in the ignition and turn it to 'ON" and wait 3 to 5 minutes until the emergency flashers stop/turn off. Afterward, you should be able to start the engine. NOTE: This does NOT reset the burglar alarm. It will go off again when you enter the vehicle without using the remote/key fob.

Trunk Lock After Closing
--------------------------
Desc.: What happens to the trunk lock when closing it.

Settings:
Yes: Automatically lock Boot on closing
No: Boot can be reopened using micro switch button located on the trunk/boot

* Trunk Lock After Drive Off
----------------------------
Desc.: Should the trunk be locked at drive off or after 30 sec.?

Settings:
Yes: Trunk/Boot will automatically lock when vehicle increases speed
No: Trunk/Boot will remain closed, however will be in the unlocked
condition if No was selected in the previous option.

* Door & Trunk Unlock at Key Out
--------------------------------
Desc.: When the is removed from the center console should door/trunk
be unlocked?

Settings:
Yes: All Doors & Trunk/Boot will Unlock when the Key is removed from
the Ignition Switch If Driver frequently locked all Doors when
driving
this feature would be beneficial.
No: Doors and Boot will remain in the same condition as they were
prior
to Key removal

* TSL Locking Logic (Theft Security Locking/Deadlock)
-------------------
Settings:
TSL at first Press: Default Setting. All Doors will lock in Deadlock
Mode
TSL at Second Press: All Doors will lock in Deadlock mode at the second
press of the Remote.

* Lock /Unlock Acknowledge
--------------------------
Settings:
None : No acknowledge will be visible
Indicators: Indicators will blink as acknowledge

* Follow Me Home Function
-------------------------
Settings:
Tail Light: When selected Tail Lights will be illuminated
Back Up Light: When Selected Reverse Light will be activated


Tech 2 Body Exterior Lighting & Horn
====================================

* High Beam Follow me home Active Time
--------------------------------------
Desc.: Follow Me Home Active Time can be adjusted between 0- 10 minutes

Settings:
This Feature can be turned on or Off .Yes / No can be selected.
Low Beam Automatic / Low Beam also in Position 0 (light switch)
Yes / No
Follow Me Home Active Time
- Daytime Driving Lights can be activated

* Parking Lights
----------------

Settings:
Act as Lead Me To the Car Light.

* Park Light On Reminder
------------------------
Settings:
On / Off
If Ignition is turned Off and the parking lights are active, Driver will
be warned if set to on.

* Show Trailer Light Outage
Desc.: REC will detect blown trailer light and display on SID

Settings:
Yes or No

* Trailer Light / Fog Light off
-------------------------------

Settings:
Yes: Fog Light Rear will be disabled When Trailer is connected Yes
No

* Horn Lock Unlock Acknowledge
------------------------------
Settings:
On: Horn will honk when car is locked
Off: Horn will not honk if car is locked


Tech 2 Body Locking
===================

* Panic Alarm Activation (Vehicles fitted with /Alarm only)
-----------------------------------------------------------
- Panic Button / Locking Switch
Central Locking Switch Driver /Passenger

Settings:
- Panic Button on Remote and locking switch inside vehicle will
activate alarm
- Panic Button will activate Alarm only
- Locking Switch inside vehicle (driver /passenger will activate
alarm only
- No Panic Alarm function required.

* Unlock Logic
--------------
Settings:
All at first press : All Doors will open & Fuel Lid will unlock if the
Driver or Passenger Door Switch is activated
Driver Door & Fuel Lid at first press : Only the drivers Door will unlock
& Fuel Lid will unlock when door
switch is activated

* Remote unlocking One Press
----------------------------
Settings:
All at first press: All Doors will open & Fuel Lid will unlock if the
Remote is pressed
Driver door & Fuel Lid at first press: Only the drivers Door will unlock &
Fuel Lid will unlock when the Remote
is pressed

Starting System
The function of the starting system is to crank the engine at a speed fast enough to allow the engine to start. Heavy cables, connectors and switches are used in the system because of the large currents required.
The starting system consists of a gear reduced starter motor, battery, remote control switch (ignition switch) and relay.
Vehicles equipped with automatic transaxle have a transmission range sensor attached to the circuit which prevents operation of the starter motor unless NEUTRAL or PARK are selected.
Vehicles equipped with a manual transaxle have a start inhibit switch in the starter control circuit, which prevents operation of the starter motor unless the clutch pedal is in the applied position.
------------------------------------------------------------------------------
The anti - theft protection system provides protection from unauthorized entry into the passenger compartment.
The system is controlled by an anti - theft alarm control. When armed, unauthorized entry into the vehicle is detected by lamp switches.
Once triggered, the system flashes the headlamps, the parking lamps, the alarm indicator, and sounds the horn. In addition, the starter circuit is disabled to prevent starting the vehicle until the system is disarmed.
System Arming
The system will be armed by the remote entry transmitter when the following input sequence is followed:

1. Turn the ignition switch off and remove the key.

1. Close all doors (unlocked).

1. Press the LOCK button on a transmitter to lock doors. Alarm warning lamp will turn on.

1. Wait for the anti - theft warning lamp to turn off.

The system will also be armed when the following input sequence is followed:

1. Turn the ignition switch off and remove the key.

1. Open a door. Alarm warning lamp will flash.

1. Lock doors with power door switches. Alarm warning lamp will now glow steadily.

1. Close all doors.

1. Wait for the anti - theft warning lamp to turn off.

Opening any door will activate the alarm after the alarm is armed.
Disarming an Untriggered System
The system can be disarmed by performing one of the following procedures.

• Driver or RH front door is unlocked with a key.
• Driver door is unlocked by pressing the UNLOCK button of a remote entry transmitter.
• If remaining in the vehicle, turn the ignition switch to ON or ACC position.

System Triggering
The armed alarm system will be triggered if any door is opened without using a key or a remote entry transmitter to unlock the door first.
Disarming a Triggered System
Carry out either of the following steps will disarm the triggered alarm system.

• Driver or RH front door is unlocked with a key.
• Driver door is unlocked by pressing the UNLOCK button of a remote entry transmitter.

Two minutes and 45 seconds after the system has been triggered, the horns and exterior lamps will shut off automatically. The system will then reset to an armed state and will trigger again if another intrusion occurs.
--------------------------------------------------------------------
Passive Anti-Theft System (PATS)
The Passive Anti-Theft System (PATS), known as SecuriLock, is fully passive in operation and requires no special procedures by the driver to arm or disarm the system. It is invisible to normal scrutiny and is operated by a transponder within the key body. This communicates with the module through a transceiver mounted around the ignition switch lock barrel.
The PATS functionality is incorporated within the powertrain control module.
PATS keys contain an electronic device inside, and are physically larger than a non-PATS key.
The transponder code reading is carried out when the key is inserted into the ignition lock barrel, and turned from position 0' to position II' or III' to crank the engine. If the PCM receives the correct code signal, the engine will start. Should the code received not be recognized, the engine will not crank as the PATS is still armed and the engine immobilized.
Anti-Theft Indicator
Whenever the ignition is switched on the anti-theft indicator will remain on for three seconds while the system carries out an initial ignition key-read.
The anti-theft indicator will flash rapidly for three seconds to indicate the PATS has immobilized the vehicle.
For additional information on the PATS fault codes, refer to the Diagnosis and Testing section.

the remote control for the electric door locks should disable the alarm just lock it then unlock it, try that it might work

There is NO kill switch on the 2000 Elantra... HOWEVER, there is a thing called the Key Fob (keyless remote entry system). There is, however, a system in place called the 'starter kill' circuit and it is activated when the burglar alarm goes off.... it's called the burglar alarm relay and it is activated to prevent the engine starter system from being used. There are three ways to get the engine started in such a circumstance... 1. use the key fob to 'disarm' the system... 2. put the key in the ignition and turn it to the 'RUN" position and wait until the alarm stops (horn stops beeping and the parking lights stop flashing), then the engine will start.... 3. pull the starter relay from the UnderHood junction box and bypass the starter circuit (key in ignition and in the 'RUN' position), jumper the starter solenoid circuit to energize the solenoid to start cranking the engine -- it should start then.

some alarms have kill switches, but most of them prevent the car from even starting. i would consider strongly getting the remote for the alarm or Completely disconnect the alarm module.

Call the dealership and see what they say.

1) remote starter was not hooked up to the factory arm wire
2) trunk release was programmed to disarm factory alarm before popping trunk
3)parking light wire on remote starter was not hooked up
4)disarm wire from remote starter was not hooded up
5)this is not normal and they should fix the problem or have it done by some one else and have them pay for it, how much did they charge,
Bring it over I'll fix it right and not charge overpriced amount

try unhooking battery cable. hook back up and use key remote to unlock car and try to start if no remote use key to unlock