1997 Nissan Pathfinder Logo
Anonymous Posted on Jun 12, 2013

Problematic gears, the car is stalled not moving?

1 Answer

donald adams

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 13 Answers
  • Posted on Sep 19, 2013
donald adams
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

Joined: Sep 19, 2013
Answers
13
Questions
1
Helped
1300
Points
40

Has it or had it been sitting for a long time? if so change the fluid. let it sit over nite, then rockit back and forth in 3rd. if that dont work u might need a new tras..

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

Automatic ford ranger it starts then when you put it in gear it stalls.

One of the most common failures that can cause this problem that I have seen before is the Torque converter solenoid (TCC solenoid). This solenoid can stay stuck on and cause the torque converter to stay locked up, this will cause the vehicle to stall whenever it is put into gear. The vehicle will start and run fine in park or neutral but will stall out as soon as it is put into gear. This is the most common failure that can cause this.
Also a malfunctioning idle air control valve can cause this, if the valve isn't moving or responding to bump up the idle when put in gear it may cause the vehicle to stall out, the computer commands this valve to allow more air in to bump up the idle to compensate the load on theenginewhen put in gear, if it isn't moving or isnt moving fast enough the idle may be too low and could cause the engine to stall out.Have also seen bad crankshaft position sensor cause this ,as well as mass airflow sensor's ,TPS - throttle position sensor's . Your best bet , take it to a qualified repair an have it diagnosed . No guess work .
0helpful
1answer

Shifter is in neutral. Why is manual transmission stuck in 3rd gear?

Internal transmission breakage has stuck the thing in 3rd gear. Stalls when putting in other gears because transmission is then being put into 2 gears at once. Better look into getting another transmission of having the current unit overhauled and repaired.
0helpful
1answer

2004 jeep liberty won't move when put in gear (like brakes are locked).crank it in neutral put in gear it will go till i touch brakes then won't move again.WHAT'S WRONG WITH THIS THING.

gear, is this a Manual trans? or AUTO you said gear.
what gear, please name the gear, 1,2,3,4,5 R
or PRNDL ( a/t box auto matic) what shift lever selection?
what is out door air temp, you do know brakes can get wet and freeze right?
it wont go you meant? until brakes are touched, key word won't?

ok engine only starts in PRNDL set to N??
is that it?
and then when you shift to D, the car will not move
what about the other gears.? try them all yet?

my guess (wild) is that you dont know how park lock out works.?
that you must hold the brake pedal down to shift to park or neutral.
is that it? (read operators guide?)

my guess is car is not drive-able. key point1 (a dead car)
point 2, engine starts and runs. and races on demand with gas foot.
point 3, im lost. (no trans stated or clear symptoms.)

my jeep has 6speed manual box
and the clutch allows me to start car.
on Automatics trans must be in park or neutral to crank engine.

"it will go till i touch brakes"



I read that 10 times,
my 2nd guess. the engine stalls ?

IS THAT IT, stalls means engine RPM is 0
and right foot actions are dead.
and all dash lamps glow, telling you STALL is now.
0helpful
1answer

How do i know if my whole clutch is out on my rodeo 99?... the pedal is easy to ingage half way down and im not able to switch gears

At a standstill put the car in 3rd gear and try to get the car to move. If it stalls you clutch is fine. If you able to move the vehicle w/o stalling you need a new clutch.
0helpful
1answer

Stalling

check the idle control valve and sensor
0helpful
1answer

Car hesitates/stalls when engine is warm and car starts to move.

Sounds like a bad motor mount, pop the hood and see if the motor shakes or moves rapidly when u put it in gear holding down the brake.
0helpful
1answer

Car will idle but stalls when its put in any gear automatic transmision

It's probably a bad torque converter---that's what allows the engine to idle when transmission is still in gear. It locks when the car is moving, but if it doesnt unlock then the engine will stall out.
1helpful
1answer

When I put car in gear it sputters and stalls.

read the codes with volvo or if you would like me to guess replace the air mass meter/ck all vac hoses
Not finding what you are looking for?

47 views

Ask a Question

Usually answered in minutes!

Top Nissan Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...