Question about 1996 Ford Crown Victoria

1 Answer

96 crown vic engine light check and it was a cylinder 7 misfire what deos it mean

Got in my car and this light came on i dont know what it means i want to know what i have to buy to fix it myself

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,120 Answers

Problem with wire could be bad but plug,coil,This is #7 look there.

Posted on Jun 11, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 4 Answers

SOURCE: 2003 Ford Crown Vic Misfire

milage on this shouldn't matter, the light being on is probly just stuck, however you maay wanna check to be sure the brakes aint hangin up a little,

Also the surging can be causeed by the fuel pump goin out, may not be the case but something to look for, it will show up as random misfires as well, maybe try a good fuel addative, (could have a little water in it, check the fuel filter as well, alot of cars now days have a charcol filter and when they go bad they can be a issue, Pick up tube could also have a hole in it, the fuel pumpo on theese cars should be in the tank and are not fun to replace,

hope one of theese suggestions helps, there are many thing that can cause the problem your describing

Posted on Jan 08, 2009

chuck943

Chuck Martin

  • 783 Answers

SOURCE: engine code p0307 cylinder #7 misfire

It could be carbon deposits on valve seats keeping valves from totally closing. You can try getting you a can of motorcraft PM3 top end engine cleaner and get engine up to operating temp then remove one of the small vacuum lines from the intake and draw the contents of the can slowly into the engine.After you have drawn in the contents shut engine off and let it soak for about 45 minutes then crank it back up and let it run until it clears. Now it will smoke like a forrest fire while you are doing this so don't be alarmed,just tell the neighbors you are spraying for mosqitos.This may cure the problem. If not you may be looking at a valve job.
This can be verified with a compression test if this is what is causing it.

Posted on Feb 05, 2009

warlock61

warlock61

  • 659 Answers

SOURCE: Car is running rough, afetr spark plug change

make sure no fuel is down in the spark plug ports it will short out the spark

Posted on Apr 15, 2009

Anonymous

  • 4 Answers

SOURCE: cylinder 4 misfire on a 2000 crown victoria interceptor

first cylinder 4 is the last on the passenger side . first pull the coil out and check if there is water where the plug is. if there is take the water out and dry up the coil. if you find water you got a crack manifold or a bad intake manifold gasket. if there is no water replace the coil. good luck

Posted on Apr 28, 2009

Bruce Hathcock

  • 3600 Answers

SOURCE: 1998 crown vic police. Had check engine light with

your egr on that side is dirty try cleaning it aslo check intake boltsaround those clyinders.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

P1763 and p0303 codes for my 02 jeep grand cherokee. car is super sluggish and shakes when gets to 50mph.


no engine stated.??????????
303 is gross misfire on #3 cylinder. on all cars.
its a for sure thing, means bad combustion on #3 and its power is weak. 1763 is tranny The 7 means that. and is problem2.

ever get a 60k miles tunup this decade?
sparks plugs, spark wires, filters, air and fuel>?
spark plugs dont last life of any engine.
THE CEL blinking (oper guide tells) means that misfire
is burning the CAT converter to a crisp. (raw fuel + air does that)
the opr. guide says get it serviced, fast, dont drive fast or tow anything. all great advice in the glove box.

get a cheap tuneup, and magic can happen in most cases.
misfire has many causes. over 20.
but a tuneup not done, is 99% cause. (due to nobody doing them)
only fate , determines truth, not statistics....
for example you sucked a valve on #3..

if the new spark parts dont fix #3 a compression tests is next.
or an injector balance test say from #3 to one other injector.
all this is like 1hr work, but no engine stated, so.....

Apr 24, 2015 | 2002 Jeep Grand Cherokee

1 Answer

2002 100k m crown vic police interceptor cylinder 6 misfire


Engine Misfire diagnosis can be complex and there are many reasons for misfires to occur. I suggest you read the article at this link that deals with engine misfires and the diagnosis of them and possible solutions to repair them.

Nov 08, 2012 | 2000 Ford Crown Victoria

1 Answer

My 2002 crown vic is misfiring and the check engine light flashes when speeds of over twenty miles of hour are reached. Is it safe to drive. How can I fix this


you can drive it but it will damage your catalyst system, that is why the klight flashes to let you know other problems can develop. the car being a 2002 it has a misfire monitor in the computer. go to a local parts house and have them scan for misfire codes to see which cylinder is misfiring. make sure you check the intake at the #5 cylinder (which is the first one on the left side of the engine)to see if it is getting coolant in it from the intake leaking at the thermostat housing.

Jul 30, 2011 | 2000 Ford Crown Victoria

2 Answers

I have a 96 crown vic intercepter that is hesitating when i push on the gas.also the check engine light is flashing


When the check engine light is flashing, it means that the system has detected a misfire condition that can cause damage to the catalytic converter if not repaired. Try to drive the vehicle as little as possible until the problem can be addressed. Look for bad coil pack or shorted injector or driver

May 18, 2011 | 1996 Ford Crown Victoria

2 Answers

Hi, I'm getting codes 136 02 sensor bank 1 sensor 2 along with 301 cylinder 1 misfire and 304 cylinder 4 misfire. Could the 136 be caused by the misfires ? I'd like to just swap out the plugs, but, they...


I wouldn't worry about the 02 code it will clear when you replace the coils. to be positive that the coils are bad, swap them with another cylinder and see if that cylinder misfires. 90% of the time it's the coil. Let me know
Randy

Nov 28, 2010 | 1996 Ford Crown Victoria

2 Answers

I have a 1996 crown vic i need to know these touble codes po305 po304


P0304 means that cylinder 4 has a misfire and P0305 is a cylinder 5 misfire. What this means is you may have bad spark plugs, or bad plug wires, or you may need to replace your distributor cap and rotor. I would start with plugs and wires.

Oct 21, 2010 | 1996 Ford Crown Victoria

1 Answer

Where is the location of no. of cylinder on crown


2004 Ford Crown Victoria 4.6 liter V-8 VIN "W"

a39c7f2.gif

Hope helps (remember rated this).

Jul 19, 2010 | 1997 Ford Crown Victoria

2 Answers

I can't seem to get my check engine light to work, have replaced the bulb and sensors, 96 crown vic.


Hi,
I'm a little confused. You want it to come on?
The check engine light comes on when you have a problem with the engine or drive train. If it hasn't come on, that's a good thing. It's not meant to be a reminder to check oil or anything like that.,, Please clarify? Thanks!

Sep 17, 2009 | 1996 Ford Crown Victoria

2 Answers

Engine light po 300 code


IS THIS A 99 CROWN VIC? IF SO IS IT MISFIRING? IF THIS IS THE CASE YOU MORE THAN LICKLY NEED PLUG WIRES.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/terry_db4da071b7da3ac1

Sep 06, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...