My remote for the keyless entry does not work.

Hello Jennifer Jackson...

No... even LINCOLN windows are harder to break
(sorry... your LINCOLN is pretty secure).

Worse... the best price I've paid to get a double sided
PATS (passive anti-theft system) key cut = $6.

Bring your own key... But this was all about the price of PREVENTING your current situation... (oops).

If your ONLY key is truly "inside"...
Your goose is pretty much cooked... The cost of
the LOCKSMITH is pretty trivial compared to your
alternatives... Dealers will zing you MUCH BETTER
than your "expensive locksmith"...

But what ever you do... (my recommendation)... Since
you prefer not to be prepared... (no door code or FOB)
Don't pass on the opportunity to have that same SMITHY
at least tell you about your door code POSSIBILITIES
or at least program a remote FOB for you ...

A RESPONSIBLE "expensive locksmith" will
explain the WISDOM of NEVER having less than 2 (TWO) transponder keys. (by reading your owners manual you can program the FOBs yourself (FREE).

How do you manage the "no" keyless entry...?
I remain pretty sure the number pad... & KEY FOB
(wireless transmitter) were standard equipment...

2 SPARE keys minimum... ALWAYS.

SEALED Strattec Ford Mercury Lincoln PATS Transponder Chip Key UNCUT H72...

NEW FORD KEYLESS ENTRY CAR REMOTE FOB PAIR amp TWO UNCUT TRANSPONDER KEY...

1998 1999 2000 2001 2002 2003 Lincoln Town Car FOB Remote Transponder Car...

Carnac the Magnificent

Silly question, have you tried to replace the battery in the remote? Sounds like it's getting weaker and weaker. worth a shot.

1. Enter 5-digit permanent entry code into the keyless entry keypad.
2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.
3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.
4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).
5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

How to install a keyless entry pad on a 2004 Lincoln town car

Great news, you can program a 1994 Lincoln Town Car keyless entry remote yourself! Here are the steps:

NOTICE: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
1. Turn ignition to RUN or ACC.
(Run is forward, just shy of starting car.)
2. Momentarily jump pins in programming connector located behind the glove box.
(The connector will have two pins inside of it, and it will not be plugged into anything. Jumping the pins means to make a connection between the metal inside the plug. You can do this by using any metal, a metal paperclip bent in the shape of a "U" usually works perfect.)
All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote. Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
You can find more keyless entry remote programming instructions here https://www.keylessentryremotefob.com/Key-Fob-Programming-Instructions-s/1856.htm

are you talking about door pad keys? If yes, the permanent code is on a plastic card in your owner manual folder and on the module. Your dealer also can retrieve with his scanner for about 1/2 hour labor.

check out keylessride.com--this may help you. or you can call your local ford dealer to find out how to change code. click on keyless entry remote,

SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code

1. Enter the permanent factory keyless entry keypad code.

1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.

1. Enter the new five-digit keyless entry keypad code.

1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.

1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.

1. After all new keyless entry codes are programmed:
   • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
   • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
   • -------------------------------------------------------------

Programming —Transmitter

1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.

1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
   Press any button on the transmitter to be programmed.

1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.

1. Press the SET button on the driver door panel.

1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.

1. Press the 1 or 2 memory button on the driver door panel.

-------------------------------------------------------------
Programming —Autolock and Horn Chirp

1. NOTE: This procedure must be completed within 30 seconds.
   Turn the ignition switch to RUN.

1. Press the UNLOCK button three times.

1. Turn the ignition switch to OFF.

1. Press the UNLOCK button three times.

1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.

1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.

1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.

----------------------------------------------------------------------------------

Hello
this is how to program the remotes/keyless entry

How

• Obtain all remote transmitters
• enter the 5 digit permanent code into the keyless entry pad on the drivers door
• Press the 1-2 switch on the keyless entry pad
• Within 5 seconds
• Press any button on the first remote transmitter
• The doors should open then lock
• Within 5 seconds
• press any button on the second & third remote
• within 5 seconds for each remote
• to exit programming
• simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds

NOTE
The 5 digit permanent code is located in one of the following places

1. On the owners warranty card
2. On the label on the inside the trunk/ boot
3. On the owners code card
4. On the centrel locking control module located in the drivers door
5. In the PCM ford can get this for about $25.00

I hope this help
Regards Paul
www.limotec.co.uk

Yes there is a fuse, from the eletrical diagram i am seeing power comes from the power distrubtion box and also fuse in the Fuse box,

Check your fuses for any blown ones. Im seeing a 15amp and 20 amp fuse and a 40amp feed from the distrubtion box.