Brake light and turn signals

If both the brake lights and rear turn signals are not functioning in your 2008 Dodge Charger, there are several possible causes to consider. Here are some common issues that could lead to this problem:
1. Blown fuses: Check the fuse box for any blown fuses related to the brake lights and turn signals. A blown fuse can interrupt the circuit and prevent the lights from working. Refer to your vehicle's manual to locate the specific fuse for these functions and replace it if necessary.
2. Faulty bulbs: Inspect the bulbs in the brake lights and turn signals to see if they are burnt out or damaged. If a bulb is not working, it should be replaced. It's possible that multiple bulbs have failed simultaneously, leading to both the brake lights and turn signals not functioning.
3. Wiring issues: Check the wiring connections and harnesses for any signs of damage, loose connections, or corrosion. Faulty wiring can disrupt the electrical flow and prevent the lights from operating. Repair or replace any damaged wiring as needed.
4. Malfunctioning brake light switch: The brake light switch, located near the brake pedal, activates the brake lights when the pedal is pressed. If the switch is faulty or misaligned, it can cause the brake lights to not work. Consider having the brake light switch inspected and replaced if necessary.
5. Faulty turn signal relay: The turn signal relay controls the flashing of the turn signals. If the relay is defective, it can prevent the rear turn signals from operating. Consider replacing the turn signal relay if other potential causes have been ruled out.
If troubleshooting these common issues does not resolve the problem, it is recommended to consult a professional mechanic or authorized Dodge service center for a more accurate diagnosis and repair. They will have the expertise and necessary tools to pinpoint and fix the specific issue with your 2008 Dodge Charger's brake lights and rear turn signals.

It could be the turn signal switch, since the brake wire travels through the turn switch after it leaves the brake switch and then goes to the bulbs. That is how you get a steady brake light on one side, and a blinking light on the turning side. The rear turn signal lights and brake lights share the same filament in the bulbs (and the same wire). The wire on the turning side has to first travel through the flasher relay.
If you have a test light, first check for power out of the brake light switch with the pedal depressed. Then check for power in and power out at the turn switch connector-power in on the brake light wire and power out on either of the wires going to the rear bulbs-if no power out, the turn switch is bad-brake pedal still depressed so you still have the signal.

You put in the wrong bulb and it's feeding back.

I can almost 100% guaranty the turn signal switch is the problem. Power for the brake lights starts at the brake switch. power then splits from there and the third brake light gets power directly from the brake switch. Since the turn signal and the brake lights are on the same bulb power for the brake lights is routed through the turn signal switch. the switch depending on what position it is in will allow brake power or turn signal power to there respective left or right brake/turn bulbs.

If you hold your foot on the brake pedal and wiggle the turn signal and or play with the hazard switch the brake lights will almost always intermittently start to work. this will confirm a bad turn signal switch which is pretty common on GM vehicle with this style setup.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Most likely this is a brake light switch issue. Replace switch.

If your emergency flashers don't work, all flasher bulbs are fine, but flashing too fast, then check and replace Hazard light switch.

Replace the turn signal switch. All of these lights run threw it.

the brake lights and the rear turn signals should be the same bulb check the bulbs to make sure they are not blown does your third brake light work if all brake light are out and the bulbs are good check the brake light switch on the brake pedal

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

no disrespect but....
Check the book and make sure you are using the proper bulbs on all sides. (3957 looks just like 3956 but wont work right)

sounds like brake shift interlock is not sensing brake pedal apply so it can activate solenoid to allow shft from park.
Check bulb socket and replace if bulb ok