I'm trying to adjust the wheel alignment on my 1996 Volkswagen Jetta and can't find the castor and cambor specs.
Hope this helps
1993- 1995 2.0 Camber (1) Front ................ -0.67 ............ -1 To -0.33 Rear ................. -1.5 .......... -1.67 To -1.33 Caster (Front) (1) .... 3.42 ............ 2.92 To 3.92 Toe-In (2) Front ................ 0 (0) .......... -0.08 To 0.08 Rear .............. 0.17 (4) ........... 0.08 To 0.25 Toe-In (1) Front .................. 0 ............ -0.17 To 0.17 Rear ................. 0.33 ............. 0.17 To 0.5 1996-99 1.9L Camber (1) Front .............. -0.5 .......... -0.83 To -0.17 Rear ............... -1.5 .......... -1.67 To -1.33 Caster (Front) (1) ... 1.75 ............ 1.25 To 2.25 Toe-In (2) Front .............. 0 (0) .......... -0.08 To 0.08 Rear ............ 0.17 (4) ........... 0.08 To 0.25 Toe-In (1) Front ................ 0 ............ -0.17 To 0.17 Rear ............... 0.33 ............. 0.17 To 0.5 1996-99 2.0L Camber (1) Front .............. -0.58 ......... -0.92 To -0.25 Rear ............... -1.5 .......... -1.67 To -1.33 Caster (Front) (1) ... 1.83 ............ 1.33 To 2.33 Toe-In (2) Front .............. 0 (0) .......... -0.08 To 0.08 Rear ............ 0.17 (4) ........... 0.08 To 0.25 Toe-In (1) Front ................ 0 ............ -0.17 To 0.17 Rear ............... 0.33 ............. 0.17 To 0.5 (all years) VR6- 2.8L Camber (1) Front .............. -0.5 .......... -0.83 To -0.17 Rear ............... -1.5 .......... -1.67 To -1.33 Caster (Front) (1) ... 3.27 ............ 2.77 To 3.37 Toe-In (2) Front .............. 0 (0) .......... -0.08 To 0.08 Rear ............ 0.17 (4) ........... 0.08 To 0.25 Toe-In (1) Front ................ 0 ............ -0.17 To 0.17 Rear ............... 0.33 ............. 0.17 To 0.5 (1) - Measurement is in degrees. (2) - Measurement is in inches (mm)
×
SOURCE: loud noise at higher speeds from front left wheel
Have the wheel bearings checked, Good Luck
Testimonial: "Okay, that seems to be the everyones opinion. Gona put her up on jacks right now. "
SOURCE: where do I check the transmission fluid in a 1996
VW's are notorious for not having a dipstick in the transmissions. The units are sealed, and can only be check by the VW dealers.
Sorry, my 1998 VW Beetle had the same problem.
SOURCE: 1996 volkswagen jetta trekk no reverse
If there is a grinding noise then you have a rev. gear, sounds like a clutch issue to me.
SOURCE: Anyone know sequence and torque specs for a
Per Chiltons...
Step 1: 30 ft lbs
Step 2: 44 ft lbs
Step 3: Plus 90 degrees
Step 4: Plus 90 degrees
Here is the tightening sequence...
10 4 2 6 8
7 5 1 3 9
302 views
Usually answered in minutes!
×