Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on May 18, 2013

Twin cam marks

Nissan almera 1600 twin cam what are the marks

5 Related Answers

Anonymous

  • 23 Answers
  • Posted on Dec 24, 2008

SOURCE: timing marks 2002 sonata 4 cyl twin cam balance shaft marks

look for marks on the timeing gears there sould be a couple notches. then bring them center to center

Ad

Anonymous

  • 1 Answer
  • Posted on Jan 04, 2010

SOURCE: nissan almera problems side light

heater blowing cold air only

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Mar 05, 2010

SOURCE: nissan almera ecu light

disconnect the battery negative cable for 5 minutes

Patrick Rayome

  • 1757 Answers
  • Posted on Apr 16, 2010

SOURCE: timing marks on twin overhead cams 2.4 and crank mark.

Click on the following direct, Free Link. It has several Diagrams including the Timing Belt + Marks for your 2004 Hyundai Sonata 2.4L DOHC In-Line 4-Cylinder Engine (located on the bottom half of the Page on the Link). There are additional Diagrams that will prove to be helpful while you are doing this...

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/sonata/2004_hyundai_sonata_timing_belt_diagram_marks.htm

Testimonial: "tHANKS, tHIS WILL DO THE JOB."

Anonymous

  • 1 Answer
  • Posted on Nov 07, 2010

SOURCE: i have yellow engine warning light on 2003 nissan

Re: Nissen Micra E 04. After a cold start, a yellow light, look like an engine came on. No different to the handling of the car, what is the Yellow light for? I have driven with the light on for a week now, nothing seem amissed.
Please mail me on [email protected]

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where can i find a diagram with upper an lower timing marks for a 1998 nissan single row twin cam 16 valve

Hi,why dont you buy a haynes manuel it will give the marks and help with eney future problems that might arise,all the best.
0helpful
2answers

My Nissan Almera keeps cutting out completely whilst driving?

run the fault codes and look for cam/crank position sensors.
faulty or loose connections may cause this fault. If you have more than 1 key in the ignition then it has been known that the mass of swinging keys will switch off the ignition
(current recall on all GMC ignition switches for just this reason)
0helpful
1answer

I replaced my timing chain nd tentioner on my Nissan almera 1600 16valve 2001model but the car overheat quickly

  • I would pull the timing covers and recheck the marks and make sure they are exactly where their supposed to be. Some times the tensioner needs extra help to get the marks in place. Pry on it. If they are good. Replace the thermostat. Just a note.. I replace everything in the timing area, except gears, unless the are broken. All pulleys, belts/chains, guides, and water pump, if it is in there.
1helpful
1answer

Nissan Almera wont start with code P0345

Code 345 means the cam sensor on bank two is not sending the correct signal to the engine computer. So no spark.
If you have replaced the sensor, the problem could be the cam or the wiring from the sensor to the computer.
0helpful
1answer

Resetting after installing a radiator on nissan almera

Not sure on the Almera, but some vehicles need the light to be re-set with a scanner, it has stored the radiator fault in it's memory, trip to a garage I'm afraid.
0helpful
1answer

Air con switch in dash works only in in number 4position,its in a 1994 1600 twin cam auto.

blower relay has gone bad. as a safety pt, when relay goes bad it runs on hi only. The relay is a resistor per say
0helpful
1answer
2helpful
1answer

Cam shaft timing marks

twin cam or single? if it's single the cam gear has a notch on it it poits to top bottom crank points to 0 mark the #1 piston at TDC distributor pointing to #1 on cap and your set.
0helpful
1answer

Car will not move

did you replace the MAF mass airflow sensor ? If you did not, clean it with electronics cleaner so it won't damage the sensor. that could be the cause. also the EGR vavle would cause a problem like that.
Not finding what you are looking for?

24 views

Ask a Question

Usually answered in minutes!

Top Nissan Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...