Question about 2002 Ford Mustang

1 Answer

The Fasten Seatbelt Light on my 2002 Mustang will not shut off

The Seatbelt light on my 2002 Ford Mustang V6 will not shut off even when the seatbelt is fastend.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 40 Answers

You need to be sitting in the drivers seat, not the passenger.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I shutoff seatbelt buzzer


Fasten your seatbelt it chimes when you are driving at not buckled to remind you to fasten it!

If you need further help, reach me via phone at https://www.6ya.com/expert/james_8f14c50d9c6cdea8

Mar 07, 2015 | 2008 Ford F-150

1 Answer

Security light flashing


I have this problem if I jump in and start the car too quickly. It will shut off and the security light flashes. Thankfully it never happens when I'm on the road! I think it's related to the seatbelt switch. There's a wire under the driver seat connected to a sensor in the seatbelt buckle that tells the computer when the seatbelt is fastened. I tried spraying WD-40 into the seatbelt buckle to clean it, which helped, but it is still loose and intermittent. When it happens the remote won't do anything to get the car unlocked and started. I just have to wait ten minutes for the security system to reset itself.

Jul 21, 2014 | 2002 Saturn VUE

1 Answer

Seat bealt light on but my seat bealt is working


Reset the connector under the Pax. side front seat. This has to be done with the ignition off. 1. Buckle the seatbelt. 2. Reset connection. 3. Unbuckle the seatbelt. 4. Turn ignition switch on and watch the light reset to off. 5. If light continues off, go to the Driver side and repeat the procedure. My problem was fixed after doing procedure 1. hope that helps.

Jan 19, 2013 | 2002 Ford Escape

1 Answer

2002 ford escape airbags replaced , light still on


You need to replace the airbag control module, it is a one time use device.

Jun 21, 2017 | Cars & Trucks

2 Answers

Is there a passcode or sequence to disable the


As far as I know that seat belt warning chime and light is there for your safety and protection, it should not be bypassed in any way.
There is no by pass seqwuence or code to eliminate this safety device.
Buckle up, its the law.

May 09, 2010 | 2002 Ford Mustang

1 Answer

The seatbelt light and bell stay on even if you buckle the seatbelt. is their a way to bypass or jumper out this on a 2000 ford mustang?


seems like the connection is disconnected on the buttom of the seat that goes to the seatbelt click,make sure its connected.if that is connected then change the thing that the seatbelt goes in on the seat that clicks in cause could be jamed common problem and wont let the light or noise go of .if my info was of any help to you please leave a comment ,thankyou.

Sep 02, 2009 | 2000 Ford Mustang

1 Answer

Drivers side seatbelt connected When truck is


sensor in the seat belt bukle needs to be replaced

Aug 01, 2009 | 2004 Ford F150

2 Answers

How do I remove the panel covering seatbelt mechanics to repair seatbelt on 2003 ford mustang?


first disconnect the battery, that seat belt unit can blow up, it has an explosive charge to tighten the belt in an accident, and make sure you are static free.

most of these are held in place with just plastic clips and just takes some pushing and pulling. it should just be the bolt at the top of the belt harness that you will need tools for.

Apr 13, 2009 | 2003 Ford Mustang

1 Answer

Dome lights won't go out / 93 buick century


your doorswitch is inside the door on the striker latch. You will need to remove the door panel to access. chances are it is stuck in the closed position. Your seatbelt latch sensor has also gone bad. It is located inside the receptacle of the seatbelt. If you only want to diengage the light, look for the molex plug attached to the wire coming from the seatbelt receptacle.

Dec 24, 2008 | 1993 Buick Regal

Not finding what you are looking for?
2002 Ford Mustang Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...