Remove right front fender on 2005 odyssey

Remove fender well trim ( a few screws)
Remove front bumper COVER (not the bumper- the plastic cover)
About 14 screws. Mostly on the underside, get a creeper, and a few
on the top.

Remove the (left or right side) Headlight assembly ( a couple more screws).
One assembly contains the headlight, turn signal and running light. Unplug
the electrical connector from the assembly. All bulbs remove from the back
of the headlight assembly. Headlight is held in place by bail wire, smaller
bulbs are 1/4 turn.

Remove marker lamp and headlamp assemblies.

Remove bolts behind lamp assemblies holding fender to frame of car.
Remove bolts along seam hidden under hood.
remove left front wheel and splash guard.
remove more bolts in wheel well
open left door, remove bolts in sill by door hinges.
Take lots of wires and stuff loose from fender.
Tada, fender is removed.

once you have removed the headlight assembly and remove the bolt behind the headlight assembly, continue locating the 10mm bolts attaching the fender along the top side, along the bottom in front and behind of the tire, open the drivers side front door, look into the opening between the door hinges and with a flashlight and a long extension on your ratchet you will then remove the two bolts between the fender and door, one on top and one at the bottom. you also have to remove the retaining bolts that attach the inner fender liner to the fender.

PROBABLE CAUSE Impact to the front bumper pushes the bumper back far enough to break the washer pump hose fitting. CORRECTIVE ACTION Replace the windshield washer reservoir and washer motor with updated parts. REPAIR PROCEDURE 1. Turn the ignition switch to ACC (I) to unlock the steering column. 2. Raise the vehicle on a lift. 3. Remove the right front inner fender. Unhook and pull back the bumper for better access. CLIPS (6 places.) SCREWS (6 places.) RIGHT FRONT INNER FENDER 4. Release the hooks on the upper right side of the front bumper. 5. Remove the clip from the filler neck, then remove the filler neck. FILLER NECK CLIP WINDSHIELD WASHER RESERVOIR CLIP WASHER MOTOR CONNECTOR BOLT BOLTS WASHER TUBES 6. Remove the right front fender trim, and disconnect the washer hose from the 90-degree fitting. CLIP FRONT FENDER TRIM FRONT HOSE 7. Disconnect the 2P connector and the two washer tubes from the washer motor. 8. Remove the washer reservoir clip and the three bolts, then pull out the reservoir. 9. Assemble the new reservoir components, but do not install the filler neck. 10. Trim 85 mm off the end of the 1,260 mm washer tube only. 11. Route the washer tubes on the reservoir. NOTE: The black fitting is for the front windshield nozzles, and the white fitting is for the rear nozzle. 85 mm 12. Install the reservoir. 13. Connect the rear tube to the straight fitting in the wheelwell. 14. Connect the 2P connector to the washer motor. NEW RESERVOIR Connect the rear washer tube. CLIP BOLT 9.8 N•m (7.2 lb•ft) 15. Install the filler neck with the original clip. Connect the front washer tube to the 90-degree fitting. Then reinstall the front fender trim. WASHER FLUID DIPSTICK 2P CONNECTOR FRONT FENDER TRIM FILLER NECK CLIP

To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Side Lamp/Front Turn Signal Lamp Bulb

Removal and Installation

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.

1. Remove the 2 fender splash shield bolts.

1. Remove the 3 fender splash shield pin-type retainers.

1. Remove the screw and position the fender splash shield aside.

1. Remove the front turn lamp bulb holder from the lamp assembly.

1. Remove the front turn lamp bulb.

1. To install, reverse the removal procedure.

Front

1. Note the radio security code, then disconnect the negative battery cable.
   
2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
   
3. On V6 Odyssey models, perform the following:
   
   • Remove the grille.
     
   • Remove the pins and clips from the lower front of the bumper.
     
4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
   
5. Pull the ends of the bumper outward.
   
6. Have an assistant help guide the bumper up and away from the vehicle.
   
7. Installation is the reverse of the removal procedure.
   

If you are changing the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. If you are changing the bulb on the passenger’s side, turn the steering wheel to the left.
Use a flat-tipped screwdriver to remove the holding clip from the inner fender, and pull the inner fender cover back.
Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.
Remove the bulb from the socket by pushing it in and turning the bulb counterclockwise until it unlocks.
Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.
Test the lights to make sure the new bulb is working.
Put the inner fender cover in place.
Install the holding clip. Lock it in place by pushing on the center.

Hope this helps you.

Remove the two bolt covers on the rear pillar by prying on the bottom edge with a flat-tip screwdriver.
Remove the bolts with a Phillips head screwdriver, and remove the light assembly from the rear pillar.
Determine which of the two bulbs is burned out: turn signal or brake/taillight.
Remove the socket by turning it one-quarter turn counterclockwise.
Remove the bulb by pulling it straight out of its socket.
Push the new bulb straight into the socket until it bottoms.
Test the lights to make sure the new bulb is working.
Put the socket back into the light assembly, and turn it clockwise to lock it in place.
Install the rear light assembly in the rear pillar. Tighten the two bolts. Snap the bolt covers into position.

Hope this helps you.

open the tailgate. you will see two taps on the side of the lense assembly. pull them back and there is 2 bolts. then you need to pull the lense straight out.