At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Replaces everything new and i cant fit drums over pads. i can drive them in but then cant spin wheel. e-brake is off and even with it disconnected drums still wont fit.
You need to retract the brake shoes, via the center adjuster mechanism. As your old brake wore, the adjuster moved the shoes outward. Simply move the adjuster to retract the shoes, then slide the drum on. Then, readjust the rear shoes.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Replace the rear brake hose/s. They deteriorate on the inside and clog up. Not letting the calipers or cylinders to release. I recommend replacing the front and rear.
Your description sounds like the brakes are WAY out of adjustment. The brake cylinders need the shoes to hit the drum or they will do exactly what you describe. I always adjust the shoes until they lock the wheel, then back off until the wheel spins freely, usually 8 to 20 clicks.
is brake pedal hard to push down without engine running ,if so proceed to step two and thats to start engine and then push on brake and if pedal softer to push then the servo is working ,now if excessive pedal travel with engine running then remove the rear drums ,make sure the outside lip is cleaned out and then adjust the brake shoes manually till they rub when you turn the drum ,this will cure it but remember that it has to bed in of course new pads brake disks ,new shoes and drums it has to bed in so give it a chance .
try adjusting the rear brake shoes but.....spin the rear wheels first is u get the feeling of the shoes grabbing then releasing ( the tire gets loose then tight as u rotate it) u will need to have the drums cut on a brake lathe or replaced...when u have this done , then adjust the rear shoes until u get a slight drag on the rear wheels..go pump the brake pedal to seat the shoes if the wheel spins free adjust the shoes more an repeat until they have a slight drag after pumping the brake pedal
Sounds like the brake pads may be worn out in the front. Make sure that there is not metal to metal contact that may score the rotors. Also, check the shoes and drums for the rear brakes if so equipped.
If you need instructions on how to disassemble, let me know.
Most likely the brake shoe in that wheel is worn down to the rivets and those metal rivets are scraping on the drum. If you have a new brake shoe installed right away you will be ok. if you wait, you may also have to have the drums turned. By the way brake shoes come in pairs so they will change both front brake pads. Joe
check to make sure that you did not put both primary brake shoes on one side. it is common for the rear brake shoe to be a little larger than the front and sometimes a little thicker.
The rear brakes should last from 30000 to 60000 miles or 50000 to 100000 kms. So something is wearing out your brakes too fast. Are you doing the work or some shop. I also assume you have discs and not drums since you mention pads and calipers. I am not certain but usually you need a tool to turn the pistion in when putting in new pads. I would make sure the pads are releasing properly by raising rear of car, stepping on brakes a few times (with engine off and try see if wheels are free by spinning by hand, also try to use handbrake a few times and release it and see if wheels spin freely. Maybe rears always applied. Notice burning smell, are discs glazed from heat? Are you using really cheap pads. Also check the proportioning valve which will decrease pressure to rear brakes during hard braking. Do you notice rear wheels squeling during hard braking. Do you have antilock brake system? Also are you using good quality pads and rotors.
×