97 NZ new, Nissan Sentra Q with erratic RPM indication.

Here is a color diagram of the distributor plug for a 1997 Nissan Sentra GA16DE:
Pin 1: Black/White wire - Ignition pulse signal Pin 2: Green/Red wire - Ignition coil power Pin 3: Black/Yellow wire - Ground Pin 4: Blue/Yellow wire - Engine speed sensor signal Pin 5: Yellow wire - Power supply Pin 6: Green/White wire - Ignition coil signal Pin 7: Red wire - Power supply
Please note that wire colors may vary depending on the specific vehicle and wiring harness. It's always recommended to double-check with a wiring diagram or a professional mechanic before making any electrical connections.

Hi Again,here's a link to a Oem mass air flow sensor from Ebay,it has the part number on it,just mouse over to enlarge to see numbers good,has a good price of 30 dollars used,Ebay is great in returning parts if they don't work,I have returned some hinges that wouldn't work on my door,hope this helps you. 1996 Nissan Sentra 1 6L DOHC Mass Airflow Sensor

computer probly needs to be flashed or reprogrammd to sync w new motor---some independent shops have the factory gear to do this-dealers only go back like 5yrs

Hello and welcome to FixYa!

If the check engine light is on then there's definitely a problem. The engine rpm is erratic right? This can be caused by a faulty MAF (mass air flow) sensor. If the MAF sensor is faulty the idle will surely be erratic and may cause stalling.

You will need to have it replaced to make the vehicle back to it's normal operation again.

Hope this helps and thank you for using FixYa! Have a good one!

Hi. This issue has several causes, but the oil light indicator is a strong sign of low pressure in the engine. This will cause the engine lubrication rate to drop, thus, producing a illuminated oil light, and erratic Oil pressure readings. The necessary actions are to have a manual oil pressure test ran on this engine, asap. When running a manual oil pressure test, you will discover if the true oil pressure is low, or normal. If the test proves that the oil pressure is, indeed, low, this will confirm that the Oil pump is suspect.

Now, if the true readings given during the manual oil pressure test are indicating that the pressure is normal, this will be the result of a failed sending unit(oil pressure switch). Although the oil pressure is suspect, this is not your only issue here. There seems to be a abnormal compression rate, present. This is causing the rough idle, and erratic RPMs. I recommend to administer a engine block compression test, as well. This test will discover if , indeed, there are issues within the cylinder heads, and block structure, such as a worn head gasket, cylinder wall issues, and cracked block. Normally, these issue will send signs, like white, or gray smoke out the tail pipe, or discolored oil. It will, also, promote erratic RPM ratings, and a rough idle. Have the oil pressure test, and engine block compression test ran, asap.

Once the test are administered, you will be able to isolate the actual problem areas, more accurately. Check the spark plug wire sets, and ignition assembly for faults, also...

Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

1.6L (GA16DE) and 2.0L (SR20DE) Engines
The thermostat is housed in the water outlet casting on the cylinder head on most models. On the GA16DE engines, the thermostat is housed in the water outlet casting attached to the water pump.



Fig. : Thermostat and housing-SR20DE engine





Fig. : Thermostat and housing-GA16DE engine




Fig. : Always make certain the jiggle valve is on the top side-GA16DE engine shown

Hope this helps (remember rated this).

Hello there:
no this is a intank fuel pump
Location: In-Tank Type: In-Tank, Electric, Direct OE Replacement Condition: New Part#: REPN314501 $70.00
FITS (ENGINE/CHASSIS)

1994: E; 4Cyl 1.6L GAS, FI, VIN "E", GA16DE;

1994: GXE; 4Cyl 1.6L GAS, FI, VIN "E", GA16DE;

1994: SE-R; 4Cyl 2.0L GAS, FI, VIN "G", SR20DE;

1994: SE; 4Cyl 1.6L GAS, FI, VIN "E", GA16DE;

1994: XE; 4Cyl 1.6L GAS, FI, VIN "E", GA16DE;

1994: Limited Edition; 4Cyl 1.6L GAS, FI, VIN "E", GA16DE;

GA16DE and SR20DE Engines



1. Start the engine and allow it to reach normal operating temperature.
2. Run the engine at 2000 rpm for 2 minutes and return to idle.
3. Turn the engine OFF and disconnect the throttle position sensor harness connector.
4. Start the engine and race the engine to 2000 rpm, 3 times.
5. Connect a timing light to the No. 1 spark plug wire and battery.
6. Loosen the distributor hold-down bolt and adjust the ignition timing to 10 degrees BTDC for the GA16DE and 15 degrees for the SR20DE engines.
7. Turn the engine OFF and reconnect the throttle position sensor harness.

_Ricky got this from the web

is it a manual or automatic?if it's manual check clutch.if it is automatic check transmission fluid.