Question about 1999 Honda Accord

1 Answer

Moonroof Visor is loose

My 1999 Honda Accord has a moonroof visor that squeaks and is loose. I have tried tightening the bolts that attach to the visor itself, but have discovered that the U hooks that attach the visor to my moonroof are loose. How can those be tightened if any? I'm so tired of it making noise, and have tried wd-40.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 6,360 Answers
Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 1999 Honda Accord - sunroof/moonroof doesn't close

This is a re-post from what I told someone else:

I took mine in expecting to have it repaired and it turns out that it was just the screws along the left and right-hand side of the panel. They were loose. The guy told me that "it eventually happens" and that "it's only a matter of time". He went on to say that "it shouldn't happen again". So, check the screws on either side of the panel right where it's stopping. I suspect that this is prohibiting yours from closing as well.

HTH!

Posted on Aug 21, 2009

  • 9 Answers

SOURCE: What is tightening torque of harmonic bal. bolt 1990 Honda Accord

1990 Honda accord
L4 2156cc 2.2ltr engine
crankshaft pulley bolt
apply engine oil to threads (a few drops)
tighten to 159 ft lbs
please rate my answer as I am new
Thanks,
Chris

Posted on Aug 29, 2009

Testimonial: "Thanks for your answer. 159ft-lbs seems a bit high. I only say this because 1990 Honda Integra 1.8L is 130ft-lbs. Maybe because of bigger engine."

fileset
  • 2 Answers

SOURCE: how do i tighten belts on 1997 honda accord?

to tighten the thin belt, loosen the top and then the bottom nuts that go through to the frame. The turn the bolt on top, the closest to the front of the car, clockwise. Then tighten both through bolts up. For the thick belt, loosen the through bolt on the alternator, then turn the long bolt at the bottom, front of car, of alternator clockwise.

Posted on Dec 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 honda accord brakes start tight up when appled


Sounds like a sticky caliper piston. Possibly the slide bolts are dry and need to be greased. These are the long shafts that hold the two pieces of the caliper together.

Jun 30, 2010 | 1999 Honda Accord

2 Answers

How do i tighten belts on 1997 honda accord?


to tighten the thin belt, loosen the top and then the bottom nuts that go through to the frame. The turn the bolt on top, the closest to the front of the car, clockwise. Then tighten both through bolts up. For the thick belt, loosen the through bolt on the alternator, then turn the long bolt at the bottom, front of car, of alternator clockwise.

Apr 22, 2010 | 1992 Honda Accord

1 Answer

My 91 honda accord is squeaking when i start it then it goes away


Hi:
That type of squeak is usually caused by a loose or slipping belt. You should check or have someone check the condition and tension on the belts and tighten them as needed. I recently put a new belt on my daughter's honda, and a couple weeks later had to re tighten it, as it stretched a bit after installation. A little more tension on it, and it is good to go now!

Jan 17, 2010 | 1995 Honda Passport

1 Answer

What is tightening torque of harmonic bal. bolt 1990 Honda Accord


1990 Honda accord
L4 2156cc 2.2ltr engine
crankshaft pulley bolt
apply engine oil to threads (a few drops)
tighten to 159 ft lbs
please rate my answer as I am new
Thanks,
Chris

Aug 29, 2009 | 1990 Honda Accord

1 Answer

1999 Honda Accord - sunroof/moonroof doesn't close all the way?


This is a re-post from what I told someone else:

I took mine in expecting to have it repaired and it turns out that it was just the screws along the left and right-hand side of the panel. They were loose. The guy told me that "it eventually happens" and that "it's only a matter of time". He went on to say that "it shouldn't happen again". So, check the screws on either side of the panel right where it's stopping. I suspect that this is prohibiting yours from closing as well.

HTH!

Jul 10, 2009 | 1999 Honda Accord

1 Answer

Sun visor won't go back into place


if its flopping around or feels loose you can try tightening the "hinge" that connects it to the roof and tightening the screws on the visor itself. That might align it enough to fit again properly.

May 26, 2009 | 2006 Kia Optima

1 Answer

Passenger side visor is coming loose.


At the Point where the Viser attaches to the Roof, There are Screws to Tighten this. There is also a Screw on the Back side of the Visor that will let you tighten the Movement of the Visor.

Jan 23, 2009 | 2003 GMC Envoy

1 Answer

Cant get my axel off


If you are referring to the axle nut on the end of the axle shaft, you may need an impact wrench, or make sure to bend the nut back (straighten out the bent section), put the car on the ground with the wheel on, and use a breaker bar, with a 3 foot piece of pipe attached (cheater bar) to loosen it. REMEMBER - some of these are reverse thread, if so you will have to go clockwise to loosen and CCW to tighten, thus, you MAY be tightening it - check the thread on the end of the shaft to tell you what way to turn the nut - if it still won't come off then you may have to use some heat, and/or chemical penetrants, but make sure you are turning it the correct way first...

Jan 06, 2009 | 1990 Honda Accord

2 Answers

Honda accord ex 92


Crankshaft pulley (harmonic balancer) removal- disconnect neg battery cable, remove belts, it would be a good idea to soak the bolt w/ penetrating oil overnight, there is a special 'crankshaft pulley holding tool' available to secure the pulley while removing and installing the bolt. Some parts stores loan tools for free if u purchase parts from them, I don't know if this is available, but it would be worth checking out. Attach holding tool and remove bolt securing pulley. Carefully remove pulley from crankshaft, Do NOT pry off. Remove key from crankshaft sprocket,
Install: install key on crankshaft sprocket, slide pulley on, apply clean oil to bolt threads but NOT to washer contact surfaces, secure crankshaft w/ holding tool, tighten to 159 ft lbs (91-93 Accord), install belts, re-attach neg cable.

Nov 11, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1999 Honda Accord Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...