Question about 2007 Hyundai Accent GS Hatchback

Open Question

Crank an cam codes for 07 hyundai accent 1.6 - 2007 Hyundai Accent GS Hatchback

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: Hyundai 2001 Accent Code - P0130

I think this is the O2 sensor - It will run fine but you might notice your gas mileage slipping and will not pass emissions.

Posted on Aug 07, 2008

  • 65 Answers

SOURCE: I changed the timing belt

If you are hearing the valves hitting the pistons then you have already done head damage but below id the marks:

Posted on Oct 04, 2008

  • 1077 Answers

SOURCE: what does code 1-p0650 mean?

P0650 Malfunction Indicator Lamp (MIL) Control Circuit Malfunction

Malfunction Indicator Lamp (MIL) is located on the instrument panel. When the ignition switch is turned ON without engine running, MIL will light up. This is a bulb check. When the engine is started, MIL should go off. If MIL remains on, the on board diagnostic system has detected an engine system malfunction.

Possible Causes:

  • Harness or connectors (MIL circuit is open or shorted.)
  • MIL bulb may be faulty
  • Posted on May 10, 2009

    • 776 Answers

    SOURCE: change the timimg belt on a 1998 hyundai accent

    Go to and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

    Posted on Jun 17, 2009

    • 1 Answer

    SOURCE: Window crank

    I had the same problem. If you look at the outside of the door while cranking the window, look to see if the window is trying to go on the outside of the outer seal. If so, you will have to check to see if the window is loose on the tracks. On mine, the track frame had spread open. I repaired it and used graphite to lube the track.

    Posted on Jul 01, 2009

    Add Your Answer

    Uploading: 0%


    Complete. Click "Add" to insert your video. Add



    Related Questions:

    1 Answer

    Three codes p0442 p0340 p0742 2006 Hyundai accent 1.6 it cranks but will not start ?

    The first code is for an evaporative emission canister leak and it might be due to a gas cap. The second one is for a cam sensor circuit problem and this will keep the vehicle from starting. The third error is for the transmission torque converter.

    Mar 11, 2016 | 2006 Hyundai Accent 1.6

    1 Answer

    I have a 2006 hyundai accent the engine died and will not restart

    known issues are broken timing belt
    first place to check
    next is to have the fault codes read to check for crank/cam position sensor failures

    Feb 18, 2018 | 2006 Hyundai Accent

    1 Answer

    2005 hyndia accent check engine light came on,1 day later car stalled and would not start. code p0340 cam shaft sensor replaced it still wont start gets spark fuel pump turns on any thoughts or suggestions...

    Check that the timing has not jumped, incorrect timing will trigger a cam sensor code as the ecu can not work out the correct position of the cam.


    Dec 02, 2010 | 2005 Hyundai Accent

    1 Answer

    Hyundai 2001 accent wont start intermittently. Replaced cam & crank sensors still no spark.Could it be key code sensor or wont engine crank if thats not right? Any other tips???

    I'd check the key at the dealership. The battery may be flat in it. Also have the key code match to the CPU checked. The security may be the problem or it may be an electical fault such as sticky starter motor brushes or a dead segment in the starter motor amature.

    Mar 18, 2010 | 2001 Hyundai Accent

    1 Answer

    We need to know where the cam timing marks go on a 1998 Hyundai Accent.The cam was turned after the belt was removed. We need to know how to aline the camshaft.


    The cam dowel should be at 12:00. the hole in the cam sprocket should be line up with the cam dowel, with cam sprocket assembled to cam, you will see looking through the cam sprocket a red marking on the head, which lines up with the dowel. Down at the crank, make sure the cut out mark on the crank spocket is lined up with the notch on the oil pump cover.

    Thanks for using FixYa - Steve

    Feb 20, 2010 | Hyundai Motor 1998 Accent

    1 Answer

    Hyundai accent 07 mp3-03 security code


    Jul 06, 2009 | Hyundai Excel Cars & Trucks

    2 Answers

    If my cam is off by 1 tooth, how can I tell? How

    Pull the upper cover off, set the engine at top dead center and see if you cams line up to the marks.

    Jun 08, 2009 | 2005 Hyundai Accent

    1 Answer

    1998 hyundai accent

    make sure crank sensor is all the way seated care taken 10mmnut dont over tighten or you will break sensor

    Sep 23, 2008 | 1997 Hyundai Accent

    Not finding what you are looking for?
    2007 Hyundai Accent GS Hatchback Logo

    Related Topics:

    80 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts


    Level 3 Expert

    85020 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides