Question about 2007 Honda CR-V EX-L

Open Question

Wheel alignment required on honda crv

Factory camber specs for front and rear wheels

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 239 Answers

SOURCE: HOWLING NOISES

Did you check your Transmission fluid and your differential fluids make sure there up and I don't know if you checked your rear wheel bearings or not, You can usually tell a wheel bearing when you are driving the car at highway speeds and you go around a corner and it get quite a bit louder Depending on what way you are turning if your turning right and it gets louder it will usually be the right side front or rear. the left usually the left front or back. some cases I have even heard Axles making a Howling Noise. Please let me know what you come up with. And Thanks in advance If I helped you out any. Bear001

Posted on Jun 17, 2008

Ad
  • 116 Answers

SOURCE: replacing front wheel bearings on a 1999 honda accord

there is a hub and a bearing assembly...usually you need to press the bearings into that hub...need a press to push out the old and press in the new...i replaced mine last year by going to the junkyard and taking out the hub and bearing assembly and just putting the whole thing into my car...much simpler..plus you learn how it goes together by taking it out in the boneyard..no press needed...plus if its genuine honda parts from a honda..(you can match the markings) its likely to be a very good part for a long time. Being used isn't always a bad thing as far as honda parts are concerned.This is from my own experience hope this helps you.

Posted on Mar 12, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 39 Answers

SOURCE: 2003 Honda CRV Bad Vibration between 35 and 50 mph

check the trans mount.

Posted on Oct 24, 2009

  • 31 Answers

SOURCE: how to replace broken stud

remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

Posted on May 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix honda crv rear camber 2007 model tires wearing on the inside?


Replace the suspension bushes on the suspension arm/s. Replace the bushes on the control arms and have a rear wheel alignment done.

Sep 01, 2014 | Honda CRV Cars & Trucks

2 Answers

Wheel alignment specs


This is just a free chat room

We have no info like that

We are at home & use the site-- the same as you do

Apr 08, 2014 | 2014 Ford Fusion

1 Answer

How to adjust rear wheel camber of honda crv 1999


its best to have an alignment shop do this, cause if it is off it will wear your tires very rapidly. good-day!

Apr 07, 2014 | 2000 Honda CR-V

1 Answer

Front Wheel Allignment


On these LH body cars, camber is not adjustable. Neither is caster. Those angles are preset by the suspension geometry. However, specifications for them ARE published. Generally, if either of those two parameters are out of spec, then it's likely something is worn or damaged and needs to be replaced.

The only adjustable parameters are to the front and rear toe but specified as "Total Toe" - see note below.
The alignment specs are as follows ...

ALIGNMENT SPECIFICATIONS AT VEHICLE CURB HEIGHT
A. FRONT WHEELS
  1. CAMBER
    Acceptable -0.6° to +0.6°
    Preferred +0.0°
    Side to Side Differential
    Acceptable 0.7° or less
    Preferred 0.0°
  2. TOTAL TOE - Specified in degrees. See Note Below
    Acceptable 0.4° in -to- 0.0° out
    Preferred 0.2° in
  3. CASTER* (reference angle)
    Acceptable +2.0° -to- +4.0°
    Preferred +3.0°
    *Side to Side Caster Difference not to exceed
    Acceptable 1.0° or less
    Preferred 0.0°
B. REAR WHEELS
  1. CAMBER
    Acceptable -0.6° -to- +0.4°
    Preferred +0.1°
  2. TOTAL TOE** - Specified in degrees. See Note Below.
    Acceptable 0.2° out -to- 0.4° in
    Preferred -0.1° in
    **TOE OUT when backed onto alignment rack is TOE IN when driving.
  3. THRUST ANGLE
    Acceptable -0.15° -to- +0.15°
Note: "Total Toe" is the arithmetic sum of the left and right Toe settings. Positive is Toe-in. Negative is Toe-out. Total Toe must be equally split between left and right wheels. Left and Right Toe must be equal to within 0.02° (2 one hundredths of a degree).

Courtesy RJK & Concorde Shop Manual

Mar 08, 2014 | 1994 Chrysler Concorde

1 Answer

Wheel alignment


If the car is stock then I would run the caster at .05 higher on the right than the left to adjust for the crown of the road. the front alignment looks good other than I am not sure which one is camber and which one is caster. To adjust the rear camber on these cars you have to have a camber kit. From the angle I am seeing you don't have a camber kit. Also the only way to adjust caster on the civic is to shift the sub frame.

Jul 30, 2013 | 1997 Honda Civic

2 Answers

I want to know how to fix the alignment on my 1995 honda accord ex.


Before making wheel alignment adjustment, perform the following checks:
  1. Tires should be equal in size and runout must not be excessive. Tires and wheels should be in balance, and inflated to manufacturer's specifications.

  2. Wheel bearings must be properly adjusted. Steering linkage and suspension must not have excessive looseness. Check for wear in tie rod ends and ball joints.
  3. Steering gear box must not have excessive play. Check and adjust to manufacturer's specifications.
  4. Vehicle must be at curb height with full fuel load and spare tire in vehicle. No extra load should be on vehicle.
  5. Vehicle must be level with floor and with suspension settled. Jounce front and rear of vehicle several times and allow it to settle to normal curb height.
  6. If steering wheel is not centered with front wheels in straight-ahead position, correct by shortening one tie rod adjusting sleeve and lengthening opposite sleeve equal amounts.
  7. Ensure wheel lug nuts are tightened to torque specifications
Ride Height Adjustment

Before adjusting alignment, check riding height. Riding height must be checked with vehicle on level floor and tires properly inflated. Passenger and luggage compartments must be unloaded. Bounce vehicle several times, and allow suspension to settle. Visually inspect vehicle from front to rear and from side to side for signs of abnormal height.
Measure riding height. See figure. Riding height between left and right sides of vehicle should vary less than 1′ (25.4 mm). If riding height is not within specification, check suspension components and repair or replace them as necessary.
Wheel Alignment Procedures

Honda recommends using commercially available computerized 4-wheel alignment equipment. Follow equipment manufacturer instructions to obtain vehicle alignment settings. Use following procedures for necessary adjustments.
Civic Camber Adjustment
Compare camber settings with vehicle manufacturer recommendations. If camber is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck camber.
Civic Caster Adjustment
DO NOT use more than 2 shims. If more than 2 shims are required to adjust caster angle, check for bent or damaged suspension components.
Compare caster settings with vehicle manufacturer recommendations. If caster is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck caster.
Civic Toe-In Adjustment

  1. Secure steering wheel in straight-ahead position. Measure front wheel toe-in. If adjustment is needed, loosen tie rod lock nuts. Turn both tie rods equally in the same direction until front wheels are in straight-ahead position and toe-in reading is correct. Tighten tie rod lock nuts. Reposition tie rod boots if twisted.
  2. Ensure parking brake is released. Check rear wheel toe-in. If adjustment is needed, hold adjusting bolt on rear compensator arm and loosen lock nut. See figure. Adjust rear toe-in by sliding rear control arm until rear toe-in is correct. Install NEW lock nut, and tighten it while holding adjusting bolt.
Wheel Alignment Specifications

  • Camber - Measurement in degrees.
    • Front: 0 (range -1 to 1)
    • Rear: 0.33 (range -1.33 to 0.67)
  • Caster - Measurement in degrees.
    • 1.17 (range 0.17 to 2.17)
  • Toe-In - Measurement in inches (mm).
    • Front: -0 (0)
    • Rear: 0.08 (2.0)
  • Toe-In - Measurement in degrees.
    • Front: 0.00 (range - 0.16 to 0.16)
  • Toe-Out On Turns - Measurement in degrees.
    • Inner: 41.00
    • Outer: 33.50
Torque Specifications Ft. Lbs (N.m)

  • Rear Control Arm Adjusting Bolt: 48 (65)
  • Spindle Nut: 136 (185)
  • Tie Rod Lock Nut: 41 (55)
  • Wheel Lug Nuts: 80 (108)
hope this helps you out.

May 09, 2011 | 1995 Honda Accord

1 Answer

Camber on left rear is out. can this be adjusted,or does it require replacement of the comtrol arm?


Rear camber is adjustable, most front end alignment shops have the required tools to bring it back to specs, HOWEVER, if you can noticeably see that the camber is out of whack, you probably lost a bushing, in which case, you would need the new arm, and a matching one for the other side, so they perform symmetrically.

Apr 21, 2011 | 2007 Honda Accord Sedan

2 Answers

How do you know if you need a 4wheel or 2wheel alignment? 2000 Mercury Cougar.


Most FWD vehicles can have a four wheel alignment performed. A 2 wheel alignment is mainly for vehicles that are rear wheel drive. There are exceptions but the 2000 Mercury Cougar is a 4 wheel alignment.

Apr 19, 2011 | 2000 Mercury Cougar

1 Answer

I have my 2005 Odyssey brought to Europe.Now I need to do aligment.Even Honda services don't have alignent settings.Is anyone there who could help me???


Alignment: Specifications
Alignment
Wheel Alignment
Tire size:
VAN, LX, EX, EX-L models: P235/65R16 103T
EX-L Touring model: P235-710R460A 104T
Tire pressure:
Front (VAN, LX, EX, EX-L Touring models) ........................................................................................................... 230 kPa (2.3 kgf/cm2, 33 psi)
Front (EX-L model) .................................................................................................................................................. 240 kPa (2.4 kgf/cm2, 35 psi)
Rear ........................................................................................................................................................................... 240 kPa (2.4 kgf/cm2, 35 psi)
Caster angle ................................................................................................................................................................................................... 2° 32' ± 1°
Camber angle:
Front ........................................................................................................................................................................................................ 0° 00' ± 30'
(Maximum difference between the front right and left side: 0° 30')
Rear ............................................................................................................................................................................................................. -0° 30' ± 45'
The camber angle can be adjusted up to ±25' (center of tolerance) by replacing one damper pinch bolt with the adjusting bolt. The camber angle can
be adjusted up to 50' by replacing both damper pinch bolts with the adjusting bolts.
Front toe-in ............................................................................................................................................................................. 0 ± 2 mm (0 ± 1/16 inch)
Rear toe-in ......................................................................................................................................................................... 2 ± 2 mm (1/16 ± 1/16 inch)
Turning angle

Inward wheel 41° 56' ±2°
Outward wheel 34° 32' (Reference)

Toe - 0° +/- 2mm

Sep 22, 2009 | 2005 Honda Odyssey

1 Answer

'95 Camaro wheel alignment specs....


its your lucky day.. i want dave mathews tickets for this :) ok for my camrao which is a 97 z28, which should work for yers heres all the tire and whell specs
Front spec
caster
set ....5.0deg +- 0.5 (+- suppose to be +on top of -)
check...5.0 +- 1.0

cross caster
set....0.0 +- 0.7
check....0.0+- 0.7

Camber
set 0.4 +- 0.5
check...0.4 +- 1.0

Cross camber
set...0.0 +- 0.7
check..0.0 +- 0.7

individual toe
set 0.0 +-0.1
cehck..0.0 +- 0.1

total toe
set 0.0 +- 0.2
check 0.0 +- 0.2

Steering wheel angle
set 0.0 +- 3.5
check ...0.0+- 3.5
i have rear specs too let me know if you need them..Anything you need to know about a f-body just let me know i have 6 manuals on them :)

Apr 07, 2009 | 1995 Chevrolet Camaro

Not finding what you are looking for?
2007 Honda CR-V EX-L Logo

Related Topics:

663 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...