I have a 1996 Nissan Altima GXE and it keeps cutting off. I had the code crank sensor and replaced it and after I did so, it fixed the problem for about a month. Now I have the code knock sensor showing up. Do the knock sensor needs replaced? I have read a couple blogs and they said to use a higher fuel grade. Could you help me so that this problem can be corrected?
SOURCE: MOSTRAR MANUAL DEL AUTO NISSAN ALTIMA GXE AÑO
Visita autozone.com (registro gratuito), selecciona año, marca, modelo y motor para acceso gratis a la informacion deseada.
Suerte.
SOURCE: How do you remove a 1999 Nissan Altima starter?
Nissan Car Altima & Sentra 1999-06
StarterRemoval & Installation
Negative battery cable
Air duct
Harness protector from the harness
Starter wiring at the starter
Starter-to-engine bolts
Starter from the vehicle
Fig. Starter location and mounting detail-3.0L Maxima with a
manual transaxle
Fig. Starter location and mounting detail-3.5L Maxima
To install:
Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on
Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short
bolt to 22-30 ft. lbs. (30-41 Nm)
Starter wiring
Harness protector
Air duct
Negative battery cable
Negative battery cable
Air inlet tube
Harness bracket
Wiring at the starter
Starter
To install:
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
1.6L & 2.0L Engines
To install:
Negative battery cable
Wiring at the starter
Bolts attaching the starter to the engine
Starter
Starter and torque the bolts to 70 inch lbs. (8 Nm)
Starter electrical connections
Negaative battery cable
1.6L, 1.8L & 2.0L Engines
To install:
Negative battery cable
Wiring at the starter
Bolts attaching the starter to the engine
Starter
Starter and torque the bolts to 70 inch lbs. (8 Nm)
Starter electrical connections
Negative battery cable
1.8L & 2.0L Engines
To install:
Negative battery cable
Wiring at the starter
Bolts attaching the starter to the engine
Starter
Starter and torque the bolts to 70 inch lbs. (8 Nm)
Starter electrical connections
Negative battery cable
2.4L & 2.5L Engines
To install:
Negative battery cable
Air inlet tube
Harness bracket
Wiring at the starter
Starter
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
2.4L Engine
To install:
Negative battery cable
Air inlet tube
Harness bracket
Wiring at the starter
Starter
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
2.5L Engine
To install:
Negative battery cable
Air cleaner cover and duct
Harness bracket
Wiring at the starter
Starter
Starter and torque the bolts to 60 inch lbs. (7 Nm)
Starter electrical connectors
Harness bracket
Air inlet tube
Negative battery cable
3.5L Engines
Negative battery cable
Air cleaner case (upper) and air cleaner to electric throttle
control actuator tube.
Harness protector from the harness
Starter wiring at the starter
Starter-to-engine bolts
Starter from the vehicle
Fig. Starter location and mounting detail-3.5L engine
continue...
SOURCE: 2001 Nissan Altima GXE turn signals comes on then goes off.
possibly the wires are loose or shot mayb try and replacing them
SOURCE: location of knock sensor on a 1996 Nissan Altima
The knock sensor is underneath the intake manifold on the rear of the engine.
If you got an engine check code from Autozone or some other goof ball company like that go and get a full tank of the highest quality gas and see if that fixes the problem.
168 views
Usually answered in minutes!
×