Combination on car keypad does not open doors

Go to your owners manual It tells you how to do it

Unfortunately, only the dealer can reset the combination. When I replaced the keypad on a Lincoln Mark VIII, I had to take it to the dealer for them to reset the combination code that had been in it. Fortunately, they did it without charging hourly rates.

go to a dealership with the title in your name they will be able to provide you with the info you need

Hi,
If you don't know the combination you're not going to have much luck there.
You might have to call a locksmith to undo your door. But I would also suggest getting a duplicate key and keeping it in a safe place. The duplicate may not can be used to start the vehicle, but it can be used to open a door if this happens again.
Hope this helps... Good luck.

Open the trunk and up under the package tray where rear speakers mount,on the passenger side you will see the module.It will be black and have 3 connectors to it.It will have a sticker on it with a 5 digit code.It will also have a sticker on one of the trunk hindges with this code if someone has not removed it.Here is how the system works:

Keyless Entry Keypad To unlock the driver front door (20124), and disarm the anti-theft alarm control (19A366) (if equipped):

• Enter the permanent factory code.
• Enter the owner's alternate code.

To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver front door or luggage compartment door (40110) . To unlock the luggage compartment door, press the 5/6 button within five seconds of unlocking the driver or passenger door(s). To turn on the interior lamps (13776) and light all illuminated components, lift either front door handle (22404) and press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time. (It is not necessary to enter the key code first.) This will turn off courtesy lamps. To program a temporary code:

• Enter permanent code.
• Within five seconds of pressing last button of permanent code, press 1/2 button.
• Enter any alternate five-digit code within five seconds of pressing 1/2 button.

In order to change the keypad number code u have to have the original code Numbers, this is printed on a tag on the key-less entry module mounted under the rear glass package tray, on a shelf inside the trunk

does the key pad light when you press a button at night? If yes, the fuse is ok.
Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
report back.

Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
--------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical

• Keyless entry keypad
• Keyless entry remote transmitter

• Central junction box (CJB) Fuse F222 (20A)
• Circuitry
• Generic electronic module (GEM)

------------------------------------------------------------------------

• No communication with generic electronic module (GEM)

• Generic electronic module.
• Circuitry.

• REFER to Section 419-10 .

------------------------------------------------------------------------------------

you will need sockets and a socket wrench, a screwdriver, jacks and jack stands, and a set of combination wrenches.

also this site should help, it's a very thorough step by step on strut removal

You will need to Find a Ford Dealership. They can Scan the Computer and Locate the Programmed Code or Reset it for you so that you can Enter your Own.

take your registration to dealer and ask them for the code. try changing batteries on key fobs