Wiper control module location

In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Have you done a Probe Test on the vehicle? A Probe Light Tester can help you locate a short in your cars electrical system. To learn what a Probe Tester is and How to use it, watch the following video: https://www.youtube.com/watch?v=tXzKcEyIOq8

Highly doubt the fuse being the problem . If the fuse is blown ,that circuit has a problem , short to ground , wiper motor drawing to much amprage . Fuse's do not blow for no reason . Fuse # 18 -30 amp . under hood fuse box . There is also a relay , wiper on/off relay in same under hood fuse box . Also wiper hi/low relay ! There is also alot of electronics involved . integrated power module , front control module , plus C.A.N bus network . How to Diagnose Controller Area Network CAN . Could be wiper / washer switch , wiper motor , communication problem , module problems , Relay problem . Google chrysler intergrated power module . they have had a lot of problems with that thing .

A wiring diagram doesn't show a relay, just a 25 amp fuse in fuse panel under driver's side of dash. Intermittent working is usually from a loose or poor or corroded connection, or the switch is old and tired, or the motor is old and tired.
Here is one way to check, if you have a test light: when the wipers are not working with wiper switch on high, and key is on, pull off the connector to the wiper/washer motor module (in the engine bay, on the firewall) and check if the purple wire has power. If it does, you probably need to replace the module. Inside the module is a park relay switch (to return wipers to down position when turned off) and a circuit breaker between the motor and ground.
If the purple wire does not have power when key is on and wipers on high, the connection is lost between the switch and the module, or the switch may be malfunctioning. The switch has 5 wires, white wire from 25 amp fuse (power in to switch), a pink wire (for the washer motor), a purple wire (high speed wipers), a dark green wire (low speed wipers), and a gray wire (for the park relay switch inside the wiper/washer motor module). If you see a yellow wire also at the module, that is part of the low speed wiper circuit (the dark green wire) coming from the park relay switch and then to the motor.
Good luck. Post back if further questions, or need more help.

located under dash at drivers right knee area

there is a body control module behind the fuse box under the dash. it runs the wioers ,widows ,and locks,and much more

I had this same problem when the sunroof was left open during a rain storm. The dealer had to replace a control module, but I was fortunately still under warranty. In the short term I would pull the fuse for the wipers when they weren't needed, located in the box by the drivers door under the dash.

First, please review this article: Where's The Fuse?

Then to answer the question you asked:
There are actually 3 fuses involved in your rear wiper system.
They are all located in the driver's fuse/relay box located under the left side of the dash.
Fuse #7, 7.5 Amp
Fuse #21, 7.5 Amp
Fuse #30, 20 Amp
These same three fuses, if blown, will also have the symptom of the front wipers not working. So if the front wipers are working, the problem has nothing to do with a blown fuse.

There are also several control units involved in making the rear wipers work:
There is the Combination Switch Control unit, the MICU Rear Junction Box Control Unit, and the Relay Control Module. These are also powered (protected) by the fuses listed above.

I would recommend Obtaining a scanner and scanning the Controller Area Network (CAN) in your vehicle to see if there are any fault codes that can help you determine why your rear wipers are not working.

If both the wiper motor and the washer motor do not work, then it is the 25 amp fuse, or the wiper control module in the dash...possibly the switch in the steering column, but I doubt that...

fuses under hood

POWER DISTRIBUTION BOX Location Name Amp Circuits Protected A Trailer Tow 50 Fuse 32/Fuse 26/Electric Brake B Fan (Hi) 60 Cooling Fan (CCRM) C Start 60 Starter Solenoid/Fuse 30/Fuse 36/Fuse 2 D Ignition 60 Fuse 6/Fuse 12/
Fuse 8/Fuse 18/Fuse 14/
Fuse 24/Fuse 20/Fuse 21/Fuse 27/Fuse 33 E Rear
Blower/
RAS 60 Rear Heater Blower Motor
Rear Air Suspension F Seat 60 Power Seats G — — Not Used H Fan-Lo 40 Engine Cooling Fans J Power Accessory 60 Fuse 13/Fuse 25/
Fuse 1/Fuse 31/Fuse 37/
Fuse 40/Fuse 7/Fuse 19 K Light 60 Headlamps/Fuse 10/
Fuse 11/Fuse 3/Fuse 9/
Fuse 23/Fuse 29/Fuse 35/Fuse 41/Fuse 17 L ABS 60 ABS Control/Pump Motor Module M Heated
Backlight 60 Heated Backlite/Fuse 16/Fuse 28/Fuse 22 N Fuel 20 PCM/Fuel Pump/CCRM P — — Not Used R PCM 15 PCM Memory S PCM 30 AX4S/Cylinder Identification Sensor/EDIS Module/PCM Power/EGR Control/HEGO's/IAC/
Injectors/MAFS/VMV T Alt./Reg. 15 Generator U Air Bag 10 Air Bag (Dedicated) V Trans. Light 10 Transmission Indicator Light W Fan 10 PCM Fan Monitor X Diode — Hood Lamp Diode Y Relay — RH Trailer Turn/Stop/Hazard Lamps Z Relay — Powertrain Control Module AA Relay — Windshield Wiper Speed BB Relay — LH Trailer Turn/Stop/Hazard Lamps CC Relay — Windshield Washer Pump Motor DD Relay — Windshield Wiper Dynamic Brake/Run
The fuses are color-coded by amp rating.

Fuse Value Amps Color Code 4 Pink 5 Tan 7.5 Brown 10 Red 15 Light Blue 20 Yellow 25 Natural 30 Light Green 40 Orange 50 Red 60 Blue