Question about 1991 Jeep Wrangler

Open Question

The Serpentine Belt keeps Shredding on my 1991 Jeep with a 4 cyl.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1991 jeep cerokee belt routing diagram

need diagram for 1995 jeep cherokee sport 4.0 without a/c, it has a/c but i want to bypass it and put smaller belt on

Posted on Sep 15, 2009

Ad
  • 31 Answers

SOURCE: What is the correct 1993 jeep wrangler serpentine

moz-screenshot-5.jpg9c0b547.gifhope this is what your looking for

Posted on Nov 18, 2009

  • 508 Answers

SOURCE: what do you loosen to remove serpentine belt from

There is an idler pulley close to the power steering. Loosen the bolt that goes through the front of the idler pulley first. Then you will see the head of a bolt looking up at you. Turn the bolt clockwise to tighten and counterclockwise to loosen. The pulley is attached to the threaded bolt and it moves the pulley up or down as needed to adjust the belt tension. When the belt is replaced turn the bolt until the belt is tight. Remember to check the belt again after a few hundred miles. A new belt will stretch and loosen.

Posted on Dec 08, 2009

  • 2926 Answers

SOURCE: I need a diagram for a serpentine belt for a 1991

ledsled378_102.jpg
1991 4 cylinder with no AC

Posted on Mar 19, 2011

  • 202 Answers

SOURCE: trying to find a diagram

There are 2 kinds, apparently: With and without A/C. Here are diagrams for both.


With AC:
mf_grimm_5.jpg



Without AC:
mf_grimm_6.jpg

Good luck.

Posted on Jul 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Free belt diagrams


http://serpentinebelthq.com/1991-jeep-wrangler-yj-4-0l-serpentine-belt-diagram/ her is a link for you to a diagram. I hope this helps

Jul 08, 2014 | 1991 Jeep Wrangler

1 Answer

Trying to find a diagram for a 1996 jeep cherokee 2.5 liter 4 cyl to replace a serpentine belt


There are 2 kinds, apparently: With and without A/C. Here are diagrams for both.


With AC:
mf_grimm_5.jpg



Without AC:
mf_grimm_6.jpg

Good luck.

Jul 23, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Serpentine belt keeps shredding (I have been


one of the pulleys might have a bad bearing, you might be able to purchase a belt kit, check all the accessories turn freely,

Apr 20, 2010 | 2005 Pontiac Grand Prix

1 Answer

What do you loosen to remove serpentine belt from 1991 jeep wrangler with ac and power steering. thanks 4 cyl. 2.5


There is an idler pulley close to the power steering. Loosen the bolt that goes through the front of the idler pulley first. Then you will see the head of a bolt looking up at you. Turn the bolt clockwise to tighten and counterclockwise to loosen. The pulley is attached to the threaded bolt and it moves the pulley up or down as needed to adjust the belt tension. When the belt is replaced turn the bolt until the belt is tight. Remember to check the belt again after a few hundred miles. A new belt will stretch and loosen.

Dec 08, 2009 | 1991 Jeep Wrangler

1 Answer

Serpentine belt keeps shredding on the inside


PULLEY ALIGNMENT.WITH BELT ON LOOK AT THE PULLEYS FROM THE SIDE.U MUST HAVE A PULLEY THE IS MISSALIGNED

May 06, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

Replacing belts


You will need to have a 3/8 drive ratchet or breaker bar to place into the idler pulley slot that is rectangular. Apply pressure to the wrench in the direction to relieve the belt tension. Slip the belt off of one of the pulleys and gently release the idler tensioner. There should be a map that shows you the belt routing on the front cowl. If you do not see it remember the belt routing as you remove it so you can replace it correctly. If it is a serpentine belt make sure the ribs of the belt are seated in all the pulleys before starting the truck.

Feb 07, 2009 | 1991 Nissan Pickup

Not finding what you are looking for?
1991 Jeep Wrangler Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...