Question about Cars & Trucks

1 Answer

97 sunfire cranks ok but wont start security light on steady

97 sunfire came in as a no start.we found a couple broken wires at the pcm repaired them and the car will crank fine but dont start the security light is on steady and at one point we got a code 1014.the voltage at the key cyl is 11.8 on the white wire and yellow has 5 vlts when cranking yellow goes to 1.8 tried to reprogram security light never flashes at all.connected tech 2 to the car and can not read data from cluster or air airbag module.SOME HELP WITH THIS ONE PLEASE

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 108 Answers

The fuse for the obd2 is usually the cig lighter ,replace fuse and connect tech 2 try reprogram if it connects!

Posted on Nov 02, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 15 Answers

SOURCE: 96 Chevy Cavalier running on 2 Cylinders

You said the the 2 cylinders in the middle has no fire. That will be 2 & 3. It has 2 coil packs. One runs 1 & 4 the other runs 2 & 3. Check the coil pack that runs 2 & 3....The firing order is 1,3,4,2... It runs because it hits,miss,hits,miss....just enough to keep it running....

Posted on Jun 28, 2009

  • 323 Answers

SOURCE: 2001 jeep cherokee want start

Dont worry about wire checks at this point. If the "no bus" message went away after disconnecting the sensor, then the sensor is bad. Replace the crank sensor and all will be good in the world again.

Posted on Jul 28, 2009

longbow243
  • 103 Answers

SOURCE: 2000 Silverado-4.3 ltre-cranks over-wont start-consistenly

Yes. First, in the fuse block under the hood check INJ A fuse and INJ B fuse. INJ A fuse is circuit 1039 which feeds the coil. If the fuse is OK, replace the coil electrical connector. I stock 2 of these at my dealership because they are needed quite often.
FYI P1351 is an ignition coil control circuit DTC.

Posted on Sep 01, 2009

  • 26 Answers

SOURCE: My 1999 Pontiac Sunfire now will not start. It

CHECK YOUR FUEL FIITER & DELIVERY SYSTEM , PUMP SOLENIOD AND OIL FUEL SENSOR

Posted on Mar 06, 2010

  • 615 Answers

SOURCE: starter wont crank on a 2000 oldsmobile intrigue

Check your manual if you have it. I believe you need to have the key in the ignition in the ON position for about 10 minutes to reset the security system.

Posted on Jul 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Pontiac Sunfire , Cranks but won't start


Have you checked for shorted wiring or burnt connectors at the PCM

Jul 01, 2016 | Pontiac Cars & Trucks

2 Answers

My corvette won't turn over got new battery.security light is on .run fine before than it shut off .


Make sure your pats key is clean. Sometimes the chip gets dirty. Also try disconnecting the battery for a couple of minutes. This will reset the system...

Jun 09, 2015 | 1990 Chevrolet Corvette

1 Answer

Can I bypass the crank sensor on a 1997 Automatic Honda Accord?


They both have crank sensors. crank sensor is the same as RPM sensor. Both cars need rpm signal. You could compare the inputs and match differences...but BYPASSING or skipping isnt ever a good idea. The 97 if I recall required crank and tdc. the 93 simply had a distributor reluctor generating both,.
WHat I recommend is you dont mix and match engines that arent compatible or change the incompatible pieces. Life is much easier both at 1st start and in the future when it needs repair.
However, you can get the crank/rpm signal from the 93 distributor, move it to the same wires ast he 97 lists, and it MAY fire. Youll still have to deal with cam and TDC, and all sorts of other incompatioble parts.. the 93 5 speed ECM should still work fine, so its a 5 speed? the engine doesnt care. Was t just not cranking because of the clutch switch input you now didnt have? You could jumper those pins (blue n black?) and bypass that. At least then all your ECM inputs are correct and in the right pins. That seems alot easier than mixing and matching year parts.

Jan 27, 2015 | 1997 Honda Accord

1 Answer

P1389 code on a 97 dodge ram 4x4 5.9. Replaced the pickup, ignition wire, asd relay and crankshaft sensor. Cap and button looked great and are only a couple months old. Truck will crank not start. Gas


are you sure that you changed the ASD relay? that code is for no signal from the ASD to the PCM. Check that you have constant 12v at the relay base and that you have switched voltage when the key is on at the relay base, then make sure you have continuity to ground at the relay base. If the relay clicks when the key is turned on then the internal coil is making and should be sending a signal to the PCM when the key is turned on.

Jul 25, 2014 | 1997 Dodge Ram 1500 Club Cab

1 Answer

2000 Sunfire, starts then stalls after replacing F.P., timing chain guides and PCM


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Oct 13, 2017 | 2000 Pontiac Sunfire

1 Answer

97 pontiac sunfire getting fire,can hear fuel pump changed fuel filter and spark plugs will turn over just wont start


did you check fuel pump relay also check your security system might be activated thinks its being stolen my daughters grand am does that once in awhile have to let it sit for 15 minuts with the key on on with out cranking it and then will start.

Feb 19, 2013 | 1997 Pontiac Sunfire

1 Answer

97 pontiac sunfire 2.4


none of that was needed to be repklaced
does your security light flashes >

May 08, 2010 | 1997 Pontiac Sunfire

4 Answers

96 jeep grand cherokee wont start


my 1996 jeep is doing the same thing.the fuse I have been changing is under hood in fuse panel on left 20 amp sm. in center of fuse panel closest to bat.

Aug 21, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22331 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...