Entrance position do not drive mercedes w220 displaying on cluster. How do I remove it?

You need a skilled auto-electrician, not a mechanic, one that has a high end scan tool computer that can analyze the stored and live data, plus reading any DTC Codes.

To me, it sound like you have a failing battery, possibly erratic charging and some bad grounds. The electronics on Mercedes are overly complex.

if only the one window
faulty door switch
or does this model have a master combination switch ?
if not the switch ..more inspection required
remove door car and check slides and guides
then motor drive

Instrument cluster removal - Mercedes - YouTube

? 2:09
www.youtube.com/watch?v=Z7vM78b5cOw
Jan 15, 2010 - Uploaded by Lim Lai Aik my instrument panel lights not working.how can I change the bulbs? thanks ... 1972 Mercedes-Benz 600 Kompressor - Jay Leno's Garage - Duration: 18:56. by ... How to convert Mercedes R129 SL ,w124 dash gauge lighting to LED ... Part 1/5 Mercedes S-Class W220 Instrument Cluster Repair - Duration: ...

Adjust the Mercedes telescoping steering wheel to the maximum extended position (maximum out position).
Move the front driver's seat to the rear-most position.
Disconnect the negative battery cable by loosening the retaining nut on the negative battery cable clamp and sliding the clamp off the battery terminal.
Remove the screws on the underside of the instrument panel cluster that hold the instrument cluster cowl in place and remove the cowl.
Remove the four screws holding the instrument cluster in place and remove the instrument cluster from the dash. Make sure to remove the electrical connectors from the back of the instrument cluster before trying to completely remove the cluster.
Turn the ignition key to the "I" position and remove the electrical plug in the back of the ignition switch. The switch should be exposed now that the cowl and instrument cluster have been removed. You will access the plug from the top of the ignition switch and cylinder assembly.
Loosen, but do not remove, the Allen bolt on top of the ignition cylinder that mates with the steering column using an Allen wrench.
Remove the two 13 mm bolts on top of the steering column. This will allow the steering column to drop down roughly 3 inches so that you can access the release button for the ignition switch.
Press the release button on the steering column where the ignition cylinder enters the column.
Turn the key to the "I" position and remove the ignition cylinder and switch assembly by pulling it out of the steering column.
Remove the ignition wiring from the back of the ignition switch and cylinder assembly by pressing down on the release tab on the electrical connector and pulling it off the switch.
Original Launch X431 iDiag Auto Diag Scanner for iPad and iPhone...

IF YOU HAVE A W220 CHASSIS S-CLASS CONTACT YOUR DEALER.SOME OF THE MODEL YEARS HAD EXTENDED WARRANTY COVERAGE FOR INSTRUMENT CLUSTER ISSUES.

pull out the instrument cluster by using the dash removal hooks. can be bought from mercedes dealer on any tool dealer like snapon or mac. all u do is to insert the hooks on either side of the instrument cluster usually on yhe lower sides and u will feel the hooks grab th instrument cluster. carefully pull the cluster out and disconnect the plug. you might have to have the steering wheel in the extended position to slide out the clucter. once you have the cluster out replace the bulb directly behind.

1.- Insert key into ignition, switch to position "1"
2.- Press the menu buttons repeatly until the mileage is displayed within the multifunction display.
3.- Press the cluster illumination button (trip reset button) 3 times in short succession. The battery voltage will be displayed and an audible signal will sound.
4.- Turn key in ignition to position "2"
5.- Press the Up and Down Arrow buttons until service menu appears.
6.- Press cluster illumination button (trip reset button) once. The oil type menu is displayed.
7.- Use the + and - buttons to select the oil used for service.
8.- Press the Up and Down buttons to confirm. The display will show : "Reset Oil Confirmation. Push Illumination button for 3 seconds".
9.- Press and hold the cluster illimination button for 3 seconds. The message "Service confirmed" is displayed.

1 key on #1 position
2 go to mph display in the cluster
3 press trip odometer knob three times (QUICK) voltage will appear on display
4 Select service menu using + or -
5 Service Indicator Displays Items
6 Press the menu systems button until the MPH display appears

With the key in position 1, hit the odometer reset button on the left on the cluster 3 times in a row. The cluster should beep once. scroll through the multifunction display with the page buttons until the display shows the onboard voltage screen. It will say something like "UB: 12.2 V" scroll threw this menu with with the up/down until you reach the "service menu" page. scroll down to "confirmation" press +, confirm full service with +. Wait till it says service confirmed. cycle the key off and then back on to position 2. Scroll to the normal service menu where it normally says how many days or miles till next service. If the service was reset correctly, it will say "service display not possible" for a few minutes while it recalculates. You must cycle the key off and back on before it will back out of the onboard diagnostic mode. If you dont back out, the esp/abs/bas lights will illuminate when the car is started

Here you find all parts, page is on W124, to select W220 use the bar at the left.
If you want a listed part list buy haynes manual.