Question about Nissan Frontier

1 Answer

2000 nissan frontier rough idle and has a po325,po300,po120,and po304

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Nissan Master
  • 450 Answers

THROTTLE POSITION SENSOR, MISFIRE, #4 MISFIRE, KNOCK SENSOR, THESE ARE YOUR TROUBLE CODES, PO120,PO300, PO304, PO325, RESPECTIVELY, REPLACE THE TPS @ THROTTLE BODY, REPLACE KNOCK SENSOR , @ ENGINE BLOCK, REPLACE YOUR SPARK PLUGS & PLUG WIRES ! AND YOU MUST ALSO REPLACE BOTH YOUR AIR & FUEL FILTERS, DISTRIBUTOR CAP & ROTOR , INSPECT, MAY NEED TO REPLACE, I WOULD ANYWAY !!!!!!!! ADD SOME GOOD FUEL INJECTOR CLEANER TO TANK, NEXT FUEL UP !

Posted on Apr 02, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 17 Answers

SOURCE: 2005 chevrolet k3500 6.6 duremax diesel with check

the codes 300 303 304 is cylinder missfire. just drive the vehicleand it will correct it self

Posted on May 05, 2009

  • 22408 Answers

SOURCE: 2000 3.3l nissan motor runs very rough, stalls,

check wiring and connection if good replace knock sensor

Posted on Nov 16, 2009

  • 2 Answers

SOURCE: change brake light bulb on a 2000 Nissan Frontier

The entire bed line will need to be removed. The long screws that hold the metal bracet where the bed extender attaches also hold the tail light assembly in place.
I pulled the bed liner up at a 45 degree angle and layed it on top of the cab. This revealed the screws. Take both screws out and lay to the side along with the metal bracket for the bed extender.
Now firmly grab the edges of the tail light assembly and pull...there are 2 hard rubber nipples that snap in to hold the assembly. You will feel like you might break it but you won't..just pull straight back hard. The assembly will "POP" out and then you can just twist the back of each bulb there are (3) and pull out..now you will see the bulbs..just pull the bad bulb straight out and push the new one into place. Now just reassemble. Total time will be 30-45 min. for this repair.

Posted on May 04, 2010

  • 14585 Answers

SOURCE: 2000 nissan frontier knock sensor code & distributor

no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Posted on Jun 14, 2010

kapishtech
  • 2272 Answers

SOURCE: 03 chevy express 6.0 misfire

P0300 Diagnostic Code - Random Misfire
Technical description:--
Random/Multiple Cylinder Misfire Detected:---
Exactly what does this code means:--
Basically this means that the the car's computer has detected that not all of the engine's cylinders are firing properly.
A P0300 diagnostic code indicates a random or multiple misfire. If the last digit is a number other than zero, it corresponds to the cylinder number that is misfiring. A P0302 code, for example, would tell you cylinder number two is misfiring. Unfortunately, a P0300 doesn't tell you specifically which cylinder(s) is/are mis-firing, nor why.
Symptoms:--
the engine may be harder to start.the engine may stumble / stumble, and/or hesitate.
other symptoms may also be present…There may be rough idle, sputters and stalls and jerks.
Causes:--
A code P0300 may mean that one or more of the following has happened:
Faulty spark plugs or wires, Faulty coil (pack), Faulty oxygen sensor(s)
Faulty fuel injector(s),Burned exhaust valve, Faulty catalytic converter(s)
Stuck/blocked EGR valve / passages, Faulty camshaft position sensor, Defective computer.
Possible solutions for this error problem:--
If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the vehicle, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.
Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or un-metered air getting past the airflow sensor, or an EGR valve that is stuck open.
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Posted on Aug 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will anyone of these codes P1320. PO325, PO300, PO510, PO120 cause a fuel injectors not to pulse?


Once you prime it and it starts will it keep running or die again until primed ?

Jul 30, 2018 | Cars & Trucks

1 Answer

2006 Audi s4 4.2l error codes po300 po303 po304 po340 and po345


P0300 - 303 - 304 engine misfire codes . P0340 Audi Camshaft Position Sensor https://www.autocodes.com/p0345_audi.html
Your best bet , take it to a qualified repair shop before you ruin the cataylitic converter

Feb 19, 2017 | 2006 Audi S4

2 Answers

Check engine soon. giving codes p0120, p1705, p0325


TPS sensor (RPM) po120,knock sensor po325.

Mar 25, 2015 | 2001 Nissan Xterra

1 Answer

Where I can locate po325 knock sensor for nissan frontier 2000


underneath intake manifold between cylinder 1 and 2.

Mar 09, 2015 | 2000 Nissan Frontier

1 Answer

How i do, my 2000 nissan frontier air bag keep on blinking


code p0325 refers to knock sensor (KS) 1 bank 1 circuit malfunction===causes wiring--poor connection--KS needs replacing.

Feb 07, 2015 | 2000 Nissan Frontier

1 Answer

2000 xterra pulling 3 codes PO174,PO300, and PO325. what type of cost am i looking at?


I had a 2001 nissan xterra in my shop,and it had the same codes. there is a very common problem with the distributor on nissan 3.3 motor. I am not sure where you are,but get a price for the distributor. I got one from ebay cheap

Oct 29, 2012 | Nissan Cars & Trucks

1 Answer

How to fix rough idling on a 2008 nissan frontier


Rough idle?Too soon,Nissan has camphase actuator,these actuator has a tendency to get plug up and creates a rough idle,You can service these actuator both intake and exhaust,with carburator cleaner or brake cleaner even gasoline,the goal is to uplug the port

Mar 10, 2012 | 2008 Nissan Frontier

1 Answer

Start runs rough short time then shut off


simply replace distributor cap and rotor button, wires and plugs. that will fix it

Oct 06, 2008 | 1998 Nissan Frontier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,018 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...